Jump to content
SAU Community

M35 Bushes Anyone Replaced Any Of Theirs

danwatt

By danwatt,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Tommy Kaira RL Mentor

Tommy Kaira RL

Posted
Posted

i dont know any part numbers but i have needed to replace my M35 needs front sway bar bushes and rack ends at 45000kms are they the same bushes that have worn out on your car. somone could ad these part numbers to the list as well thanks. im currently chasing these numbers. I just had my car serviced at North East motor Repirs and it was very interesting underneath.

danwatt Collaborator

danwatt

Posted
  • Author
Posted
i rekon any suspension place can supply swaybar bushes, just need the diametre of the bar. as for rack ends, ni$$an might be the only option

On my car the bushes that are gone are the lower compression rod bushes. Nissan want 340 each as its the arm assy. I got one from yahoo so I have the broken one spare and would like to try source a replacement part for this.

danwatt Collaborator

danwatt

Posted
  • Author
Posted
radius arm ones are common to fail and there should be after market parts in your area as they are also on 350 Z yes?

Radius arm? which ones are these? Ar they the ones most furtherest back near the driver and passenger foot wells?

I got an arm second hand ex japan $30 said it was for an NM35 when I had a look at it against mine it was different and wouldnt fit due to the front drive shafts. The bush was the same though.

danwatt Collaborator

danwatt

Posted
  • Author
Posted

did a bit of research and the c-rod I got was off a G35 or V35 which is a little different and wont fit. See picture (Black part), Im only looking to replace the bush at the end.

post-40391-1238754908_thumb.jpg

STAG250 Community Regular

STAG250

Posted
Posted
did a bit of research and the c-rod I got was off a G35 or V35 which is a little different and wont fit. See picture (Black part), Im only looking to replace the bush at the end.

yes those are the ones I just replaced for the second time, most common to wear but mine were improperly installed

available as separate part here in NZ ($70 NZ each)

that's the tie rod I just replaced below it ($200 NZ)

danwatt Collaborator

danwatt

Posted
  • Author
Posted

scoured the net and it looks like we can use these bush kits.

http://www.nengun.com/nismo/suspension-lin...-parts-350z-v35

http://www.mynismo.com/products/Default.asp?id=5348

thinking about ordering a complte kit and replacing all bush's

STAG250 Community Regular

STAG250

Posted
Posted
scoured the net and it looks like we can use these bush kits.

http://www.nengun.com/nismo/suspension-lin...-parts-350z-v35

http://www.mynismo.com/products/Default.asp?id=5348

thinking about ordering a complte kit and replacing all bush's

but read the small print:

"Designed for competition, more vibration will be transferred to the cabin"

STAG250 Community Regular

STAG250

Posted
Posted

and it looks like they're mostly supplying rear suspension bushes

many of the front bushes can only be obtained with arms/links attached but the ones I bought weren't that expensive at that time

they were:

54618AQ300 - rod assy stab m35 (one)

54668AQ300 - rod assy stab m35 (one)

54618AQ305 - rod connecting stab m35 (two)

all were $50

zei20l Grand Master

zei20l

Posted
Posted

of course more vibration will be transferred to the cabin, they are a firmer bush, soft ones absorb the vibrations, but they wear out faster. so you need to have a cup of concrete and harden up and get the poly bushes :wacko:

$50 isnt too bad, but its still a rubber bush

  • 1 month later...
oz_panda Contributor

oz_panda

Posted
Posted

I am having the same issue with the same bushes as well,

I am waiting for a quote from a JDM importer at the moment,

more liky i will be buying a new control arm as I think should be a good idea to replce the whole thing cuase i want to get a new ball join too.

danwatt Collaborator

danwatt

Posted
  • Author
Posted
I am having the same issue with the same bushes as well,

I am waiting for a quote from a JDM importer at the moment,

more liky i will be buying a new control arm as I think should be a good idea to replce the whole thing cuase i want to get a new ball join too.

I agree, the more I look into it Im going to order the genuine arms as I dont really want any problems with it. At least then I know that they wont wear out in the lifetime I have with the car. The problem is that when I costed them last they were $340 each, hope they havent gone up :)

oz_panda Contributor

oz_panda

Posted
Posted

Just got a call from the guy who i used for a long time...

he told me he can do it for $ 290 and send by ems shipping.

but then he told me if i can afforded to order another one ( LHS and RHD ) he can possibly make it a bit cheaper as in the cost would be less...

Due to the unstable econ climate, I just order one for now...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...