Jump to content
SAU Community

Re: Flutterz

R-SPEC

By R-SPEC,
in Engines & Forced Induction

 Share

Recommended Posts

R-SPEC Grand Master

R-SPEC

Posted
Posted

hoping to get some answers before r31nismoid closes this...

story: ive noticed that other skylines with similar fmic kits, pods and ss intake pipes have a lazier compressor surge whereas with mine its not as slow?

to help you understand what im saying - other skylines have a "FU..TU.TU TUTUTU mine just goes "FTFTFTFTFT" :D

i do not care about hektik flutterz. i run an atmo bov but it doesnt vent on lower rpm's so i get the compressor surge and ive noticed with other skylines at similar rpm's they have a more lazier/slower surge

question: why is this? is this normal? im just worried that maybe i havent connected something in the right place or in a right way coz the only other turbo cars that ive heard with same speed flutterz are the ones running standard intercoolers.

i'd appreciate any help

thanks

Link to comment
https://www.sau.com.au/forums/topic/264437-re-flutterz/
Share on other sites
R-SPEC Grand Master

R-SPEC

Posted
  • Author
Posted
Maybe the ones you're listening to have larger turbos?

yeah thats what i was thinking at first..

maybe shorter ic pipes or longer big diffrence in sound ive tryed it

where the hell would they fit longer piping lol i had a return flow kit before, now normal kit with alot more pipes but havent noticed any difference in sound

Do you run a air box?

nah s/s pipe -> afm -> greddy metal bend -> hks pod

Link to comment
https://www.sau.com.au/forums/topic/264437-re-flutterz/#findComment-4521118
Share on other sites
R31Nismoid Grand Master

R31Nismoid

Posted
Posted

If you know im going to close it?

Why start...

Go over to Calaisturbo.com

Its all explained there (in the "dose pipe guide")... how to get high pitch/short, low pitch/long... and so on for all your bell st kebab stand requirements.

The user is "dixie" on CT.com that created the whole thread.

Link to comment
https://www.sau.com.au/forums/topic/264437-re-flutterz/#findComment-4521163
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • sonicii
      Could it really happen......

      By sonicii · Posted

      I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • MBS206
      Could it really happen......

      By MBS206 · Posted

      Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • MBS206
      R34 25GT Engine Light 21

      By MBS206 · Posted

      Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...