Jump to content
SAU Community

Recommended Posts

They are very hard to find for the R33's. I was actually looking for some myself but have strugged to find any at all. They have the original ones but like you said they are about $600.

I know they are easy to get for the R32's. Apparently they fit an R33 but not a perfect fit.

StreetFame33

Most copies are the same its just the base plate thats different. I bought a pair from car toys for my R33 for around $170 and $20 for the base plate but the base plate didnt fit and would hang over about 30mm and looked ugly. It also made the mirrors stick in the air and didnt look good at all. I didnt like spending $550 on original ganador but once they were on it was worth it.

maybe ask Ryan from ISC Performance, he got my original ganadors for me but might be able to help you out with copies

http://www.skylinesaustralia.com/forums/IS...ance-m3987.html

Get copies is easy...try Ebay, firesport.com, nungun.com, justjap.com.au and nismo.com.au as well as other places, however, be mindful of the suitable bracket...wrong bracket means they will not fit flush and will look like shit.

  • 4 months later...

i got mine from carmate.com

at first i wasn't too happy with how they fitted, but a little messing around and painting them up made them work pretty well and i'm happy with them. more than half the price of the real ones and doesn't make much difference to me.

post-44524-1250555671_thumb.jpg

post-44524-1250555679_thumb.jpg

i got mine from carmate.com

at first i wasn't too happy with how they fitted, but a little messing around and painting them up made them work pretty well and i'm happy with them. more than half the price of the real ones and doesn't make much difference to me.

no offence mate but no way can u compare those to a real set of ganadors. i bought a set of carbon ones last month and yeh shit they are expensive but i wouldnt put anything else on my car, buying genuine u know that its gona fit. modifying cars isnt cheap but id rather do it right the first time round

^^ True i agree - but in my defense i'll say this...

At the time i wasn't a member of SAU, did most of my modifying off the bat without advice, and didn't know there was good and bad way to do things. And on a budget you find ways to take shortcuts and this is one that doesn't effect me and nobody else has said anything and really, i don't care.

Besides, the question on the thread was where can i find fakes :cool:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...