Jump to content
SAU Community

18' Enkei + Hankook $1400 S14 Manual Kit $400 S14 Ganadors $400


Recommended Posts

5 spoke Enkei's + Hankook tyres

4x 18x7.5 +38 offset 5/114 good condition

4x 225/40R18 Hankook tyres Good condition

Suit: stagea, skyline, 200sx, mazda, ford, toyota, late sti.

Swap GTR offset 17-18-19 rims + cash adj.

$1400

post-58828-1239778900_thumb.jpg

post-58828-1239780365_thumb.jpg

post-58828-1239780432_thumb.jpg

S14 manual conversion kit

S14 tailshaft, speedo drive, pedals, master and slave cylinders, lines and damper, g/box mount and cross member.

sr20det used flywheel, clutch, fork and throw out.

No box, shifter or console surround.

$400

post-58828-1239780452.jpg

S14 ganador mirrors

genuine, electric, clear mirror.

painted black, missing 1x loom.

$400

Located Gold Coast

Sam 0423 648 114

Edited by RED513
  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...

FOR SALE

18x7.5 enkei + hankooks $1200

s13 + s14 bits

SOLD:

S14a 200sx 97 300rwhp @ one stage!

S14 Hks performer coilovers

S14 Hks/kawasaki rear coilovers

S14 manual kit, looms and ecu

S14 Whiteline adj sway bars

S14 KTS rear toe & front castor arms

R32 std rims

18x8 18x9 speedy cheetahs + federals

THANKS SAU

  • 3 weeks later...


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...