Jump to content
SAU Community

Recommended Posts

Complete RB25 DET series 2 motor including all manifolds, turbo and loom. Motor came out a R33 which was crashed, Removed the engine to put into my mates S13 and before fitting to the S13 had the crank cleaned and linished and new main and big end ACL race series bearings fiitted. new gaskets (except head) throughout, timing belt and bearings done. New water pump fitted. Has been in the S13 for a few months now to run the fresh bearings in. Can see running in the car. Engine had done 114,000ks in the skyline and has only done a few thousand more in the Silvia. Motor runs great very smooth fresh motor.

$2300 for the motor Loom and Series 2 turbo

Will separate motor from loom and turbo if need be.

Call Shannon on 0450 052 809

Link to comment
https://www.sau.com.au/forums/topic/265913-rb25det-fresh-motor/
Share on other sites

  • 2 weeks later...

Hey Mate

I'm chasing the motor - i don't need the turbo or loom - woudl you be able to seperate? - also you wouldnt of happened to done a compression test on it at all.. would you?

Thanks Heaps :thumbsup:

Em :)

hey 33sxc, i went out to have a look at this engine and did a comp test. everything showed up mint the lowest was 159psi and highest was like 167 i think. all in between that

however, i asked if all new gaskets had been put on along with timing belt etc and the owner said no. so i think there has been some communication break down between 13thracer and the owner of the engine !

went for a drive in it, runs flawlessly

he also had recepts for the bottom end work done, so its legit!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...