Problem Help Needed Asap

[Stagnwagn]

hello all im new to the forum first great place with alot of info

ok the problem

the stag is the normal auto rs4 97 s1, the motor im pretty sure is dead, i have a s1 r33 skyline motor 96000ks all healthy, now looking at the two the sumps are not interchangeable (both motors are on the floor) now is there a way to fit it and if theres not is it possible to leave the front shaft off and leave it rwd until i can save up the dollars to rebuild the motor out of the stag????

don't laugh it is prob a stupid question but yeah gotta be asked

Cheers peoples

ill be on msn all day if someone can message me with some info

triangulated@hotmail.com

[unique1]

hello all im new to the forum first great place with alot of info

ok the problem

the stag is the normal auto rs4 97 s1, the motor im pretty sure is dead, i have a s1 r33 skyline motor 96000ks all healthy, now looking at the two the sumps are not interchangeable (both motors are on the floor) now is there a way to fit it and if theres not is it possible to leave the front shaft off and leave it rwd until i can save up the dollars to rebuild the motor out of the stag????

don't laugh it is prob a stupid question but yeah gotta be asked

Cheers peoples

ill be on msn all day if someone can message me with some info

triangulated@hotmail.com

Hey mate yes it is possible to run in 2wd using a 2wd sump BUT it might requires a modification to the 2wd sump around the oil pickup area im not 100% sure (just check if the pickup is in same position on 2wd and 4wd blocks and if so then your good to use it).

Next u need to take the cv joints out of the front axles (closest to the hubs) and rebolt the stub axles back into the hubs as these hold the wheel bearings in and then just leave the front driveshaft out and bolt the gearbox back on the motor as per normal.

I also think u need 2 lower brackets for the bottom bellhousing bolts but not really a necessity.

thats about all, but it will work i run a 2wd rb30 bottom end in my 4wd stagea and its fine

Edited April 25, 2009 by unique1

[Stagnwagn]

Hey mate yes it is possible to run in 2wd using a 2wd sump BUT it might requires a modification to the 2wd sump around the oil pickup area im not 100% sure (just check if the pickup is in same position on 2wd and 4wd blocks and if so then your good to use it).

Next u need to take the cv joints out of the front axles (closest to the hubs) and rebolt the stub axles back into the hubs as these hold the wheel bearings in and then just leave the front driveshaft out and bolt the gearbox back on the motor as per normal.

I also think u need 2 lower brackets for the bottom bellhousing bolts but not really a necessity.

thats about all, but it will work i run a 2wd rb30 bottom end in my 4wd stagea and its fine

yeah mate the other motor ive got has the brackets it still complet basically just gonna swap the manifolds over and do a timing belt change and service so as far as the oil pick up goes just use the 1 in the r33 s1 rb25det>???

that, have you got msn

??? just wandering if i could give you a call before i go charging out the back and start puttin it all together

[BoostdR]

just get a sump adaptor and bolt it in.

http://proengines.com.au/sumpadapter.html

[Stagnwagn]

just get a sump adaptor and bolt it in.

http://proengines.com.au/sumpadapter.html

nice kit but this is only temp while i rebuild the other motor the $900 to get this is a third of the parts cost thanks for the info tho mate much appreciated

[Stinky Rooster]

Is there any chance of getting to see a pic of the blocks side by side? Or, just a pic of the differences

Please?