Jump to content
SAU Community

Recommended Posts

I have a career opportunity that is just too good to pass up so I am reluctantly selling the "registered business" CREATIVE PLATING. Comes with all equipment which is only slightly used (a few gold & chrome jobs), website hosting & domain, www.creativeplating.com yellow pages ad, several forum advertisements etc. Alot of prospective customer contacts that have approached me with $$$$ opportunities.

Full training manuals etc. Local solution & chemical supplier details. Anybody can do it!

Selling extremely cheaply, $5000

NEEDS TO GO ASAP!

Link to comment
https://www.sau.com.au/forums/topic/268726-electro-plating-business-for-sale/
Share on other sites

Now just $3000

It has cost me more than this just for advertising in places like the yellow pages, search engine submissions, website sponsorships etc.

Only selling as I have the opportunity to open an aquarium store interstate...

See here for more details http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...em=250423738877

Edited by inmate
  • 2 weeks later...

Do a google search on Becker Maxim or check out http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...em=250423738877

I have the industrial type rectifier etc. Currently trading and all ready to go.

(You will see it being used in the videos posted on the Ebay link above)

Only reason for sale is I have been virtually given a pet shop in QLD. So I am moving interstate to run this as it means a better lifestyle for my family...

Edited by inmate
  • 1 month later...

Thread is not being deleted.

Just because you request - does not mean we honour it.

Admin's have done investigation and do not believe its reasonable, therefore it stays.

You email has been removed so you will no longer be getting emails about it.

PM me if you wish, but dont expect a reply for 2-3 weeks at least, i currently have over 50 outstanding PM's and a LOT of Admin work to do.

  • 2 weeks later...

Are you for real?

There is still PLENTY of personal info remaining in this thread.

For starters people can contact me via PM, they can email me through this site & they can get me via Ebay.

Ontop of that they have access to a personal website, a personal business, a personal cell number & a personal email all of which I am asking politely to be removed please...

Removing the thread will also save the new owner being contacted.

If you want to be a Nazi about it then atleast remove my Ebay links, the business name, website and the asking price.

That way there is no association with a personal business that I no longer own...

I really dont see what the big deal is. The thing has sold already

So to recap.

I wish to have my personal Ebay account info removed from this site.

I wish to have my old business ventures details removed from this site (name & website)

Edited by inmate
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...