Jump to content
SAU Community

Edelbrock 4" Muffler

SHZ350
 Share

Recommended Posts

SHZ350 Apprentice

SHZ350

Posted
Posted (edited)

These Edelbrock stainless steel cased mufflers represent an extraordinary change in exhaust technology. Their internal Tru-Flo core utilizes equal length runners and 409 perforated stainless steel construction. The mufflers have special ceramic packing formed around a low-turbulence dual-bypass perforated core. This design splits exhaust gasses into two separate parts that flow faster. Sound impulses are dissipated into the durable ceramic packing meaning the extra flow creates less backpressure and more horsepower.

post-58486-1241603216_thumb.jpg

MAKE ME AN OFFER!!

Edited by SHZ350
Link to comment
https://www.sau.com.au/forums/topic/268733-edelbrock-4-muffler/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      HR34 GT speedo issue

      By joshuaho96 · Posted

      Probably speedometer itself if the odometer is ticking. If the needle is stuck from a bit of grease or something that can cause it to stay at 0. Or a cracked solder joint in the speedometer can do it too.
    • Dylannn
      WTB RB25 Gearbox NSW / central west

      By Dylannn · Posted

      Thanks Fella’s   to take this off topic and to elaborate a bit more. I have an rb25/30 going into a r32 GTST.. expected to make around 600-700hp. Would you?   A) R34 GTT box   B) CD00#?  I’ve seen a few posts about the CD swap and sounds fairly involved with making it fit etc but if it’s worth the work then I’ll go that way
    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • GTSBoy
      Hypergear Turbochargers and High flow Services Development thread

      By GTSBoy · Posted

      Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
×
×
  • Create New...