Jump to content
SAU Community

Recommended Posts

can anyone recommend a someone in sydney to tune my r33 and new apexi SAFC 2???????

and also whats the average cost? keeping in mind i will install the safc myself.

also where is a good place to mount the safc?

Link to comment
https://www.sau.com.au/forums/topic/26987-safc-tuner-in-sydney/
Share on other sites

i suppose anyone with a bsic tuning knowledge could tune it. its quite easy.

But you'd need a dyno.

So you can change a setting, then see its result, then over and over again.

so contact someone with 2wd dyno and off you go.......

Unigroup engineering can dyno tune your safc. I can highly recommend them. I mounted mine on the dash above the air vents.. but if you want a more discrete look try in front of the DIN slot or to the left of the steering shroud above where your left leg goes.

Check my sig for unigroup details.

ok thanks guys.

firebladejr

which suburb is unigroup engineering in?

and i really dont want to mount the safc on top of the dash cause i dont want any holes/marks ect on the dash, and to the left of the steering shroud (above left knee) is where my gauges are mounted.

any other surgestions?

S-AFC mounts with double sided tape so you don't have to worry about holes in the dash. But the stuff that it comes with is pretty crap, I replaced it with better stuff that didn't keep falling off.

I mounted mine above my left knee under the dash. It looked really good there, like it was part of the dash.

  • 2 weeks later...

S-AFC tune usually takes around an hour. They tune the whole car, no other way to do it. You get a dyno printout.

You will still have a stalling problem, nothing I know of other than a HKS idle controller will properly eliminate this problem. You might notice some improvement after the tune but it won't be perfect.

  • 4 weeks later...

ive tried ringing unigroup but always get an answering machine. left my details 2 weeks ago and still no reply. been calling them since but just get there machine..........

  • 4 weeks later...
  • 2 weeks later...
tune takes one hour. They charged me $120ish and ran it o na dyno about 8 times. Included dyno graphs as well.

Check their website in my sig for more details.

What do u guys think of the TSI setup instead of getting a PowerFC. Would u get as much power out of it??

www.unigroup.com.au

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...