Jump to content
SAU Community

Recommended Posts

i have a set of brand new rb30et acl race fordged pistons complete kit with pins and rings and a race series head gasket 1mm steel for sale 1000ono pistons retail for $1100 head gasket $240 or so all brand new in og box and packaging.

ps i think pistons are 20thou over size check in the morning

Edited by ELMOHASA33

hi these are the specs i have if you need any more info contact david bird at mahle i did work out the comp ratio once for a twin cam head using these figures i think it was 8.5:1 but you should be able to work it out with the specs below

COMPRESSION HEIGHT: 32.100 mm

BOWL(-)/CROWN HEIGHT: -2.50 mm

BOWL/DOME VOLUME(-): 12.00cc

RING SET SERIES : M1686

PISTON LENGTH : 64.000 mm

PIN DIAMETER : 21.000 mm

David Bird

Applications Engineer

MAHLE Engine Components Australia Pty Ltd

2-8 Oxford Road, Laverton North, 3026. Victoria. Australia.

Phone: +61 (0) 3 8368 1825, Fax: +61 (0) 3 9931 1531

email: [email protected], Internet: http://www.mahle.com

this is the formula for working out compression ratio

one cylinder swept volume + deck cc + head cc

deck cc + head cc

Example: 545 + 3.378 + 48 = 596.378

3.378 + 48 = 51.378 = 11.6:1

In this example, 11.6:1

the deck cc =12ccs

neo head has 50 to 54 head ccs

using this formula and these pistons bore would be 87 stroke 85

gives a 3031 ccs with a swept volume of 505.29887 per cylinder

so 505.29887 + 12 + 50 =567.29887

12+50=62

567.29887 %

62 = 9.1:1 this is the unadjusted compression ratio "dosnt include head gasket

any change in any of these figers will change comp ratio so ceck what you have

Edited by ELMOHASA33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...