Jump to content
SAU Community

Recommended Posts

I'm looking at replacing my old system(its not original either) , with nothing flash but a slight upgrade.

So.. I want it to sound nice but dont want to spend alot. And it has to take USB mp3s, as I dont use cds anymore.

Thoughts were spending $200-$300 on a nice head set (with usb) thats grunty enough not to need a amp. And using jaycar 6.5 kevlars coaxils front and rear. I was going to put some sound deadner in the doors and not worry about a sub.

Are the original speaker wires ok or is it worth the upgrade? And is a amp really worth the $$$

Those of you that have already done systems in 2 door r33's i appriecate any ideas and comments.

Esp head set and speakers selection.

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/271513-modest-sound-system-for-r33/
Share on other sites

I don't own a 33, but I did my system in my 32GTR and its a pretty descent setup.

I think most of the headunit can drive about 50w each channel (4 speakers).

Cheapest and quickest option would be to get any name brand headunit with USB MP3...etc and wire it up using the stock wiring. You should be able to just use the factory wiring and the HU can drive the front and rear no problem. Then get dynamat extreme and deaden both doors and the rear passenger area (under the B/C pillar trim). The only complicated part would be to make the speaker adaptor for the doors.

To go a bit better, get a descent HU with at least 2v RCA pre-out for front, rear and sub, for future proofing. If you want to get an external amp (a descent one), which you might as well do everything else and install a sub.

Hunt around eBay and the FS section in this forum, some of the used sound gear come up cheap and you'll save a bit of money going 2nd hand.

Oh and can I buy a single plastic DIN filler from any shop or do I have to go to Nissan?

You mean you have a spare din not in use? Just get a single din pocket and put it in there. Most audio shops like Ryda stocks them. Does not has to be nissan.

Edited by __PhaseShiftDown
  • 2 weeks later...

So far Ive bought and installed a Pioneer usb head (thanks to jb's sales) and the jaycar 6.5 kevlar's just in the front.

Got the blank DIN and jap ariel adaptor from autobarn.

I got the 6.5s to fit with the door standard speaker mounts(with a bit of moding), and drilled the door plug to pull the cable thru.

Sound really good, still want to put put the jaycars on the back and maybe put some deadener in the door.

thanks for the advice guys.

Stock speaker wires should be ok, and sound deadener in the doors will definitely improve the bass. Try and seal the door enclosure with some rubber or similar material from Bunnings etc - cheap and works a treat!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The attached document is fine. I just downloaded & opened it.
    • Hello, sorry for being late to join the discussion, but my clock just died on me.   Ive tried to look at Michaels digital clock repair.docx and it doesnt work maybe the file has expired.   Please let me know if you can re upload it or take some youtube videos to show us how to get the clock installed? thanks
    • I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
×
×
  • Create New...