Jump to content
SAU Community

Recommended Posts

Hey,

I have an A31 here that i am in the process of getting back on the road, it has had the hicas removed, but half of the power steering stuff is still not connected.

I have this picture of my rack, i know 2 fittings go to either side of the rack but i need to know where the other 3 fittings should go to (with the hicas removed).

Which one is pressure feed?, return?, and should the remaining fitting be blocked off?

Thanks,

-matt

post-61963-1244016155_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/273056-steering-rack-in-a31/
Share on other sites

If it is a hicas rack it should have a feed and return to the pump/resevoir, and the 2 lines to each side of the rack (just like a regular front steering rack).

Then it should have 4 holes for the hicas. These holes are completely seperated from the hydraulics of the front rack. Their only function is as a connection block to join the hicas lines from the rear of the car to the hicas lines in the engine bay.

If you have no intention of refitting hicas then you can leave those 4 holes unplugged.

If you still have a hicas pump and reservoir just loop it straight from the pump to the reservoir, that way you don't have to worry about keeping the lines under the car and looping it around at the back (where the rear hicas rack was).

Alright well I double checked the rack and its only got a total of 5 fittings.

Im guessing its non hi-cas?

Would someone be able to tell me which one is feed, and are the remaining 2 both returns to the reservoir?

The rack also has a silver sticker saying "Drive PRO" but nothing else. Has anyone heard of this?

-matt

I just checked my rack, it only has 4 fittings there (and another 4 on the rear for the hicas lines).

The 2 on the left go to either side of the rack, the bottom right is supply from the pump, and the one above that is return to the reservoir.

I don't know about that top one though as my rack doesn't have that.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...