Jump to content
SAU Community

Recommended Posts

R34 GTT wheels. Tyres pretty much brand new. 225x45x17 all round. Guess 95%, no camber wear.

Comes with all center caps. Great condition. Look great on r32.

With 2x 8mm spacers to get them over your brakes on r32/r33.

I need Rims that will fit with no spacers as I need a RWC. So if you can help there let me know

Geelong area.

$400.

post-52856-1244192264_thumb.jpg

post-52856-1244192302_thumb.jpg

shouldn't r34 gt-t rims fit without spacers on 32s and 33s?

Yes i agree they should. But they dont.

Just as you tighten the wheel nuts, the inside of the wheel just rubs the rotor

3mm spacers are all you need. But i though might aswell fill the gaurds as much as i could.

Oh Oh. Sorry, I just remembered . This only apply s to Spec M skylines. thanks to the bigger brakes.

Will fit base r32 gts-t , Probly r33 aswell.

Somone correct me if im wrong. =)

Oh Oh. Sorry, I just remembered . This only apply s to Spec M skylines. thanks to the bigger brakes.

Will fit base r32 gts-t , Probly r33 aswell.

Somone correct me if im wrong. =)

i just put r34 gt-t wheels onto my r32 gts-s. they dont fit they scrape the caliper about 1mm.

i just put r34 gt-t wheels onto my r32 gts-s. they dont fit they scrape the caliper about 1mm.

Thanks for clearing that up mate, Is this a M-spec.

I have heard people have taken 2mm off the inside of the caliper to make these fit.

yer jake i have seen so many people with these on 32's and 33's. I want to know the solution also.

Hey mate, was just chatting to ya bout wheels, but it wont let me PM anymore, im not 100% sure of offset on my rims, as it doesnt tell me, but they look to be about +38 on the 17x8's and +40 on the 17x8's, so they should be very similar to your previous Black wheels you were running on your r32.

Free bump too :)

I put 33 brakes on my 32 to clear my 34gtt wheels. Before that I ran 3mm spacers and they just cleared the 32 calipers.

The 33 calipers still run very close (< 1mm clearance) so maybe variations in manufacturing tolerances could explain why some 33s have problems with clearance.

i dont think its very safe to shave the caliper, its note the 'nissan' word that scraps. its the lower part of the piston. i put spacers on to give it a clearance. it scraps the wheel about 1mm or so without the spacer. the rears fit fine with about 10 - 12mm spacing

I have stock 34 rims on my '33... I could probably slide a piece of paper inbetween the inside of the wheel and the caliper... but certainly they are *barely* not touching. =-]

interested in swap for r33 gtr rims, powder coated (properly) in satin black.

Tyres and powder coat job are around 4month.

Cash adjustment my way as well lol

YESS!!! pm'd =)

well thats gay lol. i've seen so many 32s and 33 wit hthem on and i'm pretty sure they don't wear slip on spacers.

Hey Jake, what's my car doing in your avatar? Haha.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...