Jump to content
SAU Community

Recommended Posts

Hi,

I'm looking at buying a Microtech ECU for my RB25, one has come up for sale cheap with a hand controller and loom, tuned for an RB26DETT. What issues will i have? Obviously the AFM's arent an issue, as microtechs run off MAP sensors, is the only other issue ill have with the injectors? Anything else that might be different? The ECU is mapped for 550cc injectors, which i have in my RB25, but i think the 26's would be low impedence, whereas my injectors are high impedence, this shouldnt be an issue on the microtech as its compatible with both?? So all i have to do is swap the injector plugs? Is the ignitor different, idle gear, cas?

thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/274851-rb26dett-wiring-loom-on-rb25/
Share on other sites

Things i can think of

CAS

Injectors

Knock sensors

VCT (you'd be silly not to use it)

Does your tuner know Microtech's well? If not, then are many better choices out there.

So the CAS is definately different? Does it have a different output, or is it just a different plug..? Can i put a GTR CAS on an RB25?

I'm in tas, and my preferred tuner is good with microtechs, and i need a map sensor for my setup.

To throw a spanner in the works, its for a 25/30, N/A... with fairly lumpy sticks in it, so vct isn't too much of a concern, but an external controller, or custom tuning one of the extra outputs and manually wiring it could be the solution for that.

Knock sensors, fair enough, but once again, not overly concerned, as it is N/A, and i want it consistant.

Car made 151RWKW with less compression, choked intake breathing hot air, and restrictive exhaust (2.25" press bent, triple chambers), crap headers, on stock management.

It now has twin polished 60mm tb (mandrel 2.5" pipe) CAI's with no afm (OR will have jun bellmouthed front facing plenum with 80mm throttle body, ill test performance and output from each), fujitsumoto tuned length large primary headers, joining into a 3" mandrel single muffler (mandrel perforated centre offset) exhaust, had about 40thou taken off the head, spark plugs indexed facing intake valves, cam timing adjusted and accessories underdriven.

so anyway, the injectors..., if i have the same injectors with different impedence, it will still work? Appart from that, the cas will be the issue? can anyone confirm?

Also at somestage ill build another engine with a better bottom end (oversize lightweight pistons/rods, balance), and plonk on a 26 head (for the solid lifters) with some headwork and ITB's on it and push the peak power up 1000rpm or so... Meaning ill make adapters for the loom, so the whole 26 setup is neater.

Cheers,

Hi,

I'm looking at buying a Microtech ECU for my RB25, one has come up for sale cheap with a hand controller and loom, tuned for an RB26DETT. What issues will i have? Obviously the AFM's arent an issue, as microtechs run off MAP sensors, is the only other issue ill have with the injectors? Anything else that might be different? The ECU is mapped for 550cc injectors, which i have in my RB25, but i think the 26's would be low impedence, whereas my injectors are high impedence, this shouldnt be an issue on the microtech as its compatible with both?? So all i have to do is swap the injector plugs? Is the ignitor different, idle gear, cas?

thanks in advance

I don't think you will have any issues. The CAS wires in the same way as does the knock sensors. I am actually running a S2 rb25 CAS on my gtr now. The ECU sends ground pulses to each injector to fire them regardless of low/high impedence. The drop down resistor in the GTR takes care of that, you don't need to change injector plugs on the rb25 you just wire it in the same with your 12v common back to ign relay, then each injectors ground to the corrosponding pinout on the ECU plug.

The tune will probably be out slightly because of the 25/26 difference. It will probably still run OK as the injectors are still matched but I would be getting a re-tune asap to suit your application.

You can get all the wiring diagrams off the mircoleb efi website.

I don't think you will have any issues. The CAS wires in the same way as does the knock sensors. I am actually running a S2 rb25 CAS on my gtr now. The ECU sends ground pulses to each injector to fire them regardless of low/high impedence. The drop down resistor in the GTR takes care of that, you don't need to change injector plugs on the rb25 you just wire it in the same with your 12v common back to ign relay, then each injectors ground to the corrosponding pinout on the ECU plug.

The tune will probably be out slightly because of the 25/26 difference. It will probably still run OK as the injectors are still matched but I would be getting a re-tune asap to suit your application.

You can get all the wiring diagrams off the mircoleb efi website.

awesome, thanks for that.

The car doesnt need a bullet proof race tune, just needs to be able to limp to tuner, and workshops

Are you using the 26 loom on it as well?

Im confused now. You don't need to use the 26 loom on it hey, just wire the microtech into th 25 loom. If using the 26 loom you will need to change the physical connections for injectors and knock. You will also need to by-pass the drop down resistor plug.

Cheers.

Edited by James_03

Ignitor should be fine. The LT12 has 6 ignition drivers meaning you don't have to wire the ignitor up using wasted spark like early microtechs. Use the ignitor with the loom you are using, ie GTR ignitor with the 26 loom, 25 ignitior on the 25 loom.

Both wire in the same way. Only reason I say that is I think 20/26 ignitors have a different plug to 25 S1. 20/25 S1/26 coils are all the same.

Edited by James_03
Ignitor should be fine. The LT12 has 6 ignition drivers meaning you don't have to wire the ignitor up using wasted spark like early microtechs. Use the ignitor with the loom you are using, ie GTR ignitor with the 26 loom, 25 ignitior on the 25 loom.

Both wire in the same way. Only reason I say that is I think 20/26 ignitors have a different plug to 25 S1. 20/25 S1/26 coils are all the same.

uhk, ill be using the RB26 loom, so rb20 have the same as the 26? As i have an rb20 silvertop ignitor sitting on my fridge...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...