Jump to content
SAU Community

Recommended Posts

R33 with 3582r (i will check housing size 2moro for you) 18psi but with 264 cams.

Fuel reg on a r33 is good for high 300rwkw so your reg is not the issue.

post-34927-1245240645_thumb.jpg

Edited by URAS

Yeah, thanks for that. Doesnt matter what gear youre running , it all comes down to a proper tune doesn't it? Funny thing is this guy has one of the best reputations in Melbourne and the results to prove it, but i highly doubt that he tuned my car. Anyway i will post both dynos once i get it retuned elsewhere.

It's put in 4th gear so the tuner is able to tune it.

For example, you would not be able to tune a car in 1st gear because power just comes on way too quick.

Yes it does matter what gear you're in, 1st and 2nd gear will have much different power graphs compared to 4th gear.

Take it to another tuner to get a second opinion. Maybe something was wrong with the car (i.e. detonation) so the tuner had to pull timing out of it, hence the low power?

Maybe there's carbon build up in your engine causing pinging, or a hot spot on the piston.

Take it to another tuner, if he tells you he couldn't pull anything more than 250rwkw without it pinging of its tits, then somethings wrong with your car.

The fun and games begin.

Yeah thats exactly what im going to do. He said everything was fine, that there werent any issues and was actually quite happy. Its not that i want more power, cause its fine the way it is. Its just that i believe that with this set up (barring any issues such as the ones you mentioned) the car should have pulled more than it did. As i said i really got the impression it was done in rush to get the car out of there, and im sure it wasnt tuned by Mark himself.. I'll be booking it in this week sometime elsewhere..just for peace of mind!

got same setup, apart from I got the 0.82 A/R. I have a VERY conservative tune (f#$k all timing, and running rich, knock doesnt go over 15) and I made 312 rwkw at 17 PSI.

I suggest you go see another tuner.

the 0.82 makes 300 easy the 0.63 does not.

Edited by URAS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Let large companies that are making money off selling kits do the preliminary engineering for you. If they all do -10, then that is all you'll ever need. 
    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
×
×
  • Create New...