Jump to content
SAU Community

For Sale - Front Lower Arm Bar Brace - D-project

tiels32
 Share

Recommended Posts

tiels32 Contributor

tiels32

Posted
Posted

Item is brand new - Retails at $139 for individual item. Brought for an old project - have moved on. Purchased as a package with other rear end suspension components from nissansilvia.com. Bar fits Silvia 180sx 200sx S13 S14 S15 Skyline R32 R33 R34 Cefiro A31 300ZX Z32. Threaded left hand and right hand in middle for adjustability..........................The Front Lower Arm Bar adds more front end chassis rigidity when cornering/drifting. Helps keep the front suspension geometry constant - essentially a strut brace for your suspension. *Made from a 4140 Cro-molly steel, the D-Project Front Lower Arm Bar Brace will increase front chassis rigidity and front tyre grip! *Benefits: Rigid front chassis = More Front Grip= More Angle = BETTER SLIDES with more control! *Quality construction - Centre Turn Buckle Adjustment - enables you to pre-load the tension rod housings for high corner loads. As item is advertised elsewhere I reserve the right to end the auction early. Cheers.........Payment on pickup is fine or can post at your cost.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      Before starting any work, we attempted to adjust the tune. However even after adjusting it to certain extremes like completely stopping fuel, it had no effect. What fixed it was removing the Nistune Board and installing the original EPROM instead. This immediately fixed the issue. Everything should have been fine with the Nistune Board installation, so I am unsure why it has caused a problem. The soldered connector is also properly soldered. This worked when I first got the 550cc injectors, before cleaning, but that may have been a coincidence.  We ended up not installing the fuel pump hanger (at least for now). So currently running stock injectors, stock fuel pump, stock fuel pump hanger – Well everything stock except the exhaust. Now I have around €1400 in Nistune, Injectors, and Hanger collecting dust for the time being, perhaps I'll install them in the future. For now I'll enjoy the car as is 😁 Thanks a lot for all your assistance, I really appreciate all the help you have given me.
    • Piggaz
      Why am I hitting a power wall with my stroked RB25?

      By Piggaz · Posted

      The turbo can’t be the issue. They’re proven to make much much power than you’re making. There is something in the setup that isn’t correct. - has the exhaust got any silly step downs? - what exhaust manifold?
    • r32-25t
      Why am I hitting a power wall with my stroked RB25?

      By r32-25t · Posted

      Ok, just the way you wrote it made it look like you had the stagger the wrong way around 
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I was getting anxious with the DVLA not knowing if the paperwork is fine or not, so I rang them. No update had been given, but I  was reassured that providing the box was ticked on the V750 then the application will go through fine. I've been checking the DVLA website pretty much every day, in the hope that it would have been done. Fast forward to Monday 29th  and I was greeted with a new screen on the check, and it finally showed as Taxed and MOT'd, woohoo! The car was in desperate need of a clean, not knowing when this day was coming it was put off. As far as I was concerned I had another 3 weeks  I'm not normally one for using snow foam, but I wanted to give it another try It hasn't cleaned up too bad considering it's 21 years old and lived on a boat for a number of weeks. The personalised number plate is J2 XBK, an illegally spaced number plate would have it read J2X BK. BK could either represent  the colour black or Baker, which is my surname. I filmed the first drive, the Youtube link will be at the end. I used the same driving route I did with the 323F V6 when I had a new exhaust installed, heres a couple of photos A few more since then Youtube video can be viewed here: https://www.youtube.com/watch?v=TjkFHPzjGDw
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Kelford 246-A2. 262in/272ex. 
×
×
  • Create New...