Jump to content
SAU Community

Recommended Posts

i think i have the piping side of it understood.

the "T" piece goes on the pipe that runs to the wastegate actuator? is that all i have to do.. Put the T piece in there? Do i have to remove the factory boost control solenoid? If so, how?

Does the positive wire from the dsbc go into the "in" or "off" side of the switch? im guessing "off"? then from the other switch connection it is meant to run to a "fused 12 volt ignition supply", what should i connect this one too?

Thanks,

when you did it, was the pipe that the T piece goes in too big to fit tightly over the t peice connections?

Or is the pipe quite thick?

also on one end of the "T" it says "remove the factory boost control solenoid". How did u do that? in the diagram it just has the T from the pressure source to the wastgate actuator.

I hooked it up the way i thought it was meant to be.. Like in my preety diagram.. i didnt remove the factory boost control solenoid.

I was almost in tears when i took it for a test drive.. I got around the corner went to take off and i heard a bang and a lot of air. I saw the boost guage jump to 1.1 bar!!

After i got my dad to tow me back home (cracking my front bar doing so) my mate pointed out the inlet pipe had blown off...I guess i was preety blind to miss that.

Well it is all good so far, i dont have the switch hooked up yet, im just setting my high boost.. I will only use this on a cool night. I have it set at .85 bar

My boost goes from .9bar at about 4000rpm, then as the revs go up the boost drops all the way down to .6bar at 6800rpm? Could there be a boost leak? From the stock bov maby?

Your diagram is right (but you didn't show the negative connection on the solenoid) :D

R32s don't have a boost control solenoid so don't worry too much.

I have a switchable single stage turbo smart wired in the same way. Be careful how much boost you wind in, limit yourself to just under 1 bar max. If the power ramps up too quickly (like mine at 16 psi) it will start to ping. You probably wont be able to hear it when driving ( i couldn't) but on a dyno the operator will spot it.

Second thing is don't worry about your boost dropping off, it's just that the stock wastegate actuator cant hold that level of boost. Mine did it too. You'll need to swap it for an HKS adjustable or something similar to hold any sort of decent boost at the top end.

thanks BHDave i feel heaps beter now, cuz im no mechanic, i just dont like to pay ppl to do stuff that i can do myself.

I just took her out for a run then.. I had the bc turned 5 clicks which gave me .9bar of boost.. It ran very smoothly and the boost came on alot stronger (obviously). I know .9 bar is pushing the stock turbo, but i will only use it occasionaly. I have turned the bc down now to run .6bar until i get the switch hooked up.

Is .6bar normal for stock boost?

What power supply should i use for the switch?

BHDave: What did u do to keep your boost at a constant level?

Where should the boost guage "T" go for the best reading?

See picture.

Before i even hooked up the bc, i got a reading of .6bar boost?

I guessing that is too high?

I have heard the r32 stock boost is a bit higher than the others?

Like about 8-9psi?

I have my bc turned all the way down (0 clicks) today i took off in 3rd and it went to .8bar boost?

It seems to be reading higher than it should be.

What gear should i test my boost level in? cuz i know the higher the gear the higher the boost reading will be.

I have installed an HKS adjustable actuator to hold boost better at the top end. It's currently set for 12psi base pressure with the boostcontroller set up to give a quicker spool up and higher bost in the midrange but it still drops off to about 13psi at 6500 rpm. It doesn't matter too much as the turbo is running out of puff by about 6000rpm once you start to up the boost/power. My dyno curve drops off quite rapidly after about 6000rpm. Peak power of 164.2rwkw on 11-12psi at about 5800rpm

.6bar will be fine on the stock intercooler, set to about .9-.95 once you get an intercooler for high boost.

I think your gauge should be ok where it is but i have mine tapped into the fuel regulator line (the one at the front). As long as you are reading pressure off the plenum after the throttle body so you are getting a boost/vacuum signal.

Use third gear so you aren't getting too fast on the road to check pressure at 6-7000. 4th at about 120 will give you a fair indication of your turbo response/lag. Longer intercooler pipes will mean slower response once you fit a frontmount.

Hook the switch up to any switched wire under the dash, your stereo power on wire should do it.

Anythin that switches on when you turn on the ignition/acc will have a switched power line.

If you have a non original stereo it'll be easier because most have a wiring diagram on the top. There is always a wire that switches the stereo on/off with ignition, it'll tell you on the top of the stereo. Find that one and splice into it. Run that wire to one side of the BC switch. Run the wire off the other side off the switch to the solenoid (blue wire from memory). Then connect the brown wire to a ground(basically anywhere on the body, just sand off a bit of paint so you get a good connection).

Thats about it. The solenoid only pulls about 1 amp so it isn't really going to overload anything.

Zman, you can get rid of the boost controller if you have an adjustable actuator. Stock one isn't adjustable, but i don't know what sort of car you have so that doesn't mean much

last night i tried to hook up the switch to the lighter for power.. i ended up blowing a fuse.. I unhooked everything (including +/- lighter points, so nothing is touching anything else, and when i go to put a new fuse in, it blows straight away? Whats goin on there?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...