Jump to content
SAU Community

S2 Stagea Tein Coilovers

Whatever I Like
 Share

Recommended Posts

Whatever I Like Enthusiast

Whatever I Like

Posted
Posted

Hey Guys

I have in my posession a set of adjustable Tein coilovers to suit a Series 2 Stagea.

They are used but still in good condition.

I'm asking $1000 as they are Tein and are good quality.

Throw some offers at me.

Will try to get some pics up over the wknd when I'm off work.

Cheers Jason

Link to comment
https://www.sau.com.au/forums/topic/278516-s2-stagea-tein-coilovers/
Share on other sites
Import Monster Mentor

Import Monster

Posted
Posted
Hey Guys

I have in my posession a set of adjustable Tein coilovers to suit a Series 2 Stagea.

They are used but still in good condition.

I'm asking $1000 as they are Tein and are good quality.

Throw some offers at me.

Will try to get some pics up over the wknd when I'm off work.

Cheers Jason

just found my rear left shock is leaking like a sieve so your timing is great! Do you know what model Teins they are mate? DO they have damper adjustment and seperate height and spring compression adjustment?

Whatever I Like Enthusiast

Whatever I Like

Posted
  • Author
Posted
just found my rear left shock is leaking like a sieve so your timing is great! Do you know what model Teins they are mate? DO they have damper adjustment and seperate height and spring compression adjustment?

All I can gather from model is that they have Type HA written on them.

Not too sure about compression adjustment.

They have the damper adjustment hex on top.

Import Monster Mentor

Import Monster

Posted
Posted
All I can gather from model is that they have Type HA written on them.

Not too sure about compression adjustment.

They have the damper adjustment hex on top.

no probs, they're Tein HA then - a little firmer than I was wanting so I'll pass for now mate, thanks anyway :thumbsup:

Whatever I Like Enthusiast

Whatever I Like

Posted
  • Author
Posted (edited)
no probs, they're Tein HA then - a little firmer than I was wanting so I'll pass for now mate, thanks anyway :thumbsup:

No dramas dude.

If anybody is interested pm me or give me a call on 0422784684 (no private number calls please)

Edited by Whatever I Like
Whatever I Like Enthusiast

Whatever I Like

Posted
  • Author
Posted
Will they suit a RS4S?

ie fork rears and eyelette fronts?

Couldn't tell you if they'll fit rs4s.

I have the rs4v which is what I know they are to suit.

I'll have a good look at them tomorrow and get some pics for you.

Whatever I Like Enthusiast

Whatever I Like

Posted
  • Author
Posted
Will they suit a RS4S?

ie fork rears and eyelette fronts?

Unfortuneately they won't fit the RS4-S as they are both eyelet ends.

I'm taking this item off sale as I need new suspension in my car and can't wait around for a sale to buy a new set.

Needed a fairly quick sale.

Sorry to anyone who sees this and was interested.

MODS PLEASE DELETE...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • MBS206
      Chris' Toyota Mark ii JZX110

      By MBS206 · Posted

      I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...