Jump to content
SAU Community

Recommended Posts

Hey Guys, have got a few things for sale, will keep adding to the list as i find more stuff

R32 GTR Crank Angle Sensor $50 1 SOLD, still have 1 more

12x Coil packs $80 for the lot all good, pick and choose for what you want

R32 GTR Steering Rack with tie rod ends $150

LH Door(White and complete) $220

Bare steering column $20, Indicator stalk etc sold

Glovebox Lid $5

Tailights(White Surrounds) $50 each or $90 pair

STD Fuel Pump $70

Drivers Side Headlight $70

Starter Motor $50

Front Crossmember $100

STD Turbo dump pipes(pipes that bolt directly onto turbos) $50 pair

HICAS Computer $50

ATTESSA Computer $50

G-Sensor Located under Centre Console $250

Bilstein Front Shocks and springs(Dont Ask what the spring rate is and im not testing them either as im selling them cheap) $50 pair

Harmonic Balancers x2 good condition for both $20each

Near complete rear cradle, minus shocks and the HICAS setup(including rod ends etc) Diff good, rear brakes good $1200

Plastic Pipe that runs across front of car to the Twin BOV $50

I/Cooler hose from bottom of under left side guard to intercooler $20

I/Cooler hose from intercooler to under right hand side of guard $20

I/Cooler hose from above to the plenum $20

Carbon fuel canistor $10

Power Steering resevoir $10

Factory power steering cooler $10

AC Fan $20

Plastic crossover pipe that runs to BOV $30

R32 GTR BOV's $80

Widscreen washer bottle $5

Wiper Motor $50

Bonnet latch assembly $80

Left and right rear/side panel trims. NOT the quarter window trims but the other ones that are right behind the seat Couple small marks but good condition otherwise, have got Black Vinyl/leather (NOT SURE WHAT MATERIAL IT IS) inserts instead of the normal blue velour trim $50 pair

Thanks guys, also: still wrecking white R32 GTR, heap of bits sold but still some bits etc on there

Link to comment
https://www.sau.com.au/forums/topic/279669-r32-gtr-bits-and-pieces-sale/
Share on other sites

Pm replied pointa, if you need to contact me email; [email protected]

Cannot rely to pms till after 4.30 tomorrow due to the forums system....

All good happy with deal. :thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...