Jump to content
SAU Community

Recommended Posts

Hey guys i think it was a year ago i saw a R33 GTST sun roof diy tutorial but now i can't find it just wondering where can i find it? and does ne one know how i can fix my sun roof atm it doesn't tilt up or down and leaks water through the sun roof control panel how ever the sun roof still goes back and forward sometimes needs helps any info would be great :)

Cheers

Chi

Link to comment
https://www.sau.com.au/forums/topic/282177-sun-roof/
Share on other sites

These guys might be some help, seen good reviews all around Perth of them:

http://www.prestigesunroofswa.com.au/

Take off the control panel, dunno about the Liners', but most Nissans have like a flathead screw you can turn to close the sunroof if it gets stuck open.

If its leaking as well you're probably f**ked with water damage though :P

Checked the drain pipes to make sure theyre not clogged ? Theyre in both A and both C pillars, and come out at the wheel.

Link to comment
https://www.sau.com.au/forums/topic/282177-sun-roof/#findComment-4753956
Share on other sites

If its water seals I think you need new glass, as you can't get the seal alone.

Pull the whole assembly out, check the roof for water damage, hopefully you dont have any rust, clear out the drain pipes with high pressure air or water (dont forgot, if water builds up in the pillars, you're in alot deeper shit than 1.4K), check the sunroof controls and maybe get a new one if the eletronics are damaged, then finally, rip the actual sunroof apart and check if the cable is jammed or twisted anywhere, make sure the rails are all sweet, etc.

Devote atleast one day, if not a weekend, to the job.

Good luck :banana:

Link to comment
https://www.sau.com.au/forums/topic/282177-sun-roof/#findComment-4756210
Share on other sites

dude, got a 32 with a sunroof (not sure if its the same as yours) i had 100% same problem as you, i did everything you discussed as well as.... on mine looking from the outside in, the glass sits in like a frame and water builds up and just sits there so i got that black silicone stuff they stick windscreens down with and neatly put a thin strip the whole way around between the glass and that frame.

fixed the bulk of the problem

hope this helps

Link to comment
https://www.sau.com.au/forums/topic/282177-sun-roof/#findComment-4756261
Share on other sites

Just pull the assembly out an rebuild it. Does it sit uneven the whole way or more to one side? probably the cable out of line, can maybe even correct it without removing the assembly from the roof ?

Even if the pillars arent blocked, use the opportunity to flush them.

Link to comment
https://www.sau.com.au/forums/topic/282177-sun-roof/#findComment-4758399
Share on other sites

yeah i will :P hmmm how do i flush them lol? i danno how to pull the WHOLE assembly off lol do you know how? i wanan rebuild it aye lol get my roof working and pimp it out :P ahh well if ur up for some week end sun roof repairing let me know buy u a carton or something ;)

Link to comment
https://www.sau.com.au/forums/topic/282177-sun-roof/#findComment-4758470
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...