Jump to content
SAU Community

Decc Inspection

R33Gangstar

By R33Gangstar,
in South Australia

 Share

Recommended Posts

R33Gangstar Enthusiast

R33Gangstar

Posted
Posted

So i got pulled for driving a skyline (i think its like a 1,000,000 demerit point fine) and the F#!KSTICK of a cop has sent me to a DECC inspection (EPA inspection)

the most irritating thing is, i was as polite as and he still gave me all this crap like he has a hate on anyone that drives a skyline.

ive pretty much changed every thing on my car and i also have it engineered believing this will keeep me a $2000 safety bribe from cops .

HOWEVER, as i have just found out, this report means nothing to the DECC (dudes eating C**KS constantly)

so im interested if anyone knows of a way around this inspection or has had one.

i have heard one way but it's a little risk-kay and would like to heard your stories with this issue.

regards COP-H8R

Link to comment
https://www.sau.com.au/forums/topic/283422-decc-inspection/
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Ok guys thank you very much. GCG highflow it is then 🙂 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...