Jump to content
SAU Community

Recommended Posts

  • Replies 55
  • Created
  • Last Reply

Top Posters In This Topic

sideskirt pods,at the rear of the front wheel arches.there not apart of the skirts,they are missing in the photos you posted.you have them matey?

so they go on the guards ? then yes i have them will throw a pic up when i get home tonight

ok items sold so far

dayz bar

dayz pods(pending payment)

Radiator

transmission fluid cooler

slat Grill(pending payment)

xeon headlights(pending payment)

Tail lights(pending payment)

Centre console

to the person that sent me the text saying they wanted the tail lights, due to you not answering your phone for 2 days and a couple of other purchase requests for these lights, i will be selling them to the first person to come through with payment.

sorry but i think if you were serious you would be making yourself contactable

payment should go thro for pods and grill soon,im also after the rear seat lever release cover (plastic thing that surrounds it) on the passanger side in the boot

that makes fark all sense,want a picture of it?

payment should go thro for pods and grill soon,im also after the rear seat lever release cover (plastic thing that surrounds it) on the passanger side in the boot

that makes fark all sense,want a picture of it?

nah i have two kids, am getting good at deciphering sht ... the surround from the handle that folds the seats forward .. no problem will throw it in with the pods and grill

Looking for spare tyre bolt down thingy, plastic housing for fuel pump that sits inside the tank, and airbox (or just the snorkel). PM me prices if you wish (flood control won't let my PM you yet).

:P

sweet :) getting my rust cut open in a few days, its its bad might need to replace the whole lot :P

Be carful TJ

RWD front strut towers are totally different to AWD strut towers.

So is the front suspension setup.

PM sent

I need your contact details

Where in Brisbane is the car?

pm replied, car is in ipswich contact me on 0400 416 092

following items are sold

gearbox

diff

all 4 doors

slat grill

couple of trim bits

centre console

interior light

all other parts are still available

and due to ridiculous prices to post parts it may take me a day to confirm postage costs - $ 40 to post a grill to adelaide :down:

teach me for packing it properly

turbo is also now sold pending payment - taking offers for the rest of the car or on individual parts - xeon headlights still available, as are the tail lights and numerous other parts

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...