Jump to content
SAU Community

Recommended Posts

- Rims sold

- 3071r update needs rebuild will also throw in oil drain, braided water n oil lines. intake pipe, intercooler pipe also near new stainless manifold for. prefer to sell together for $1000 ono

Edited by 8znR33

hey guys n girls i have for sale: (preffer not to post but maybe able to org postage if u want to pay for it but must recieve money b4 postage)

- Garrett 3071r .86 rear .50 front

Basically brand new only been on car for dyno no shaft play/getting a TD06 25G instead

comes with lowmount manifold to suit rb25, water lines oil lines, actuator

$1900 ono ( hit me wit an offer but no low ballers plz)

- R33 front drivers and passenger seats

no rips or tears great condition

$400 ono for both

- KKR480 turbo

great condition minimal to no shaft play

$650 ono

- 5 Spoke rims suit R33 17x9.5, 17x 8.5 or 9 from jap land

bit of gutter rash (from previous owner) but other wise good condition, no tyres

$450 ono

Pictures avail on request but wll try to get it on here asap. plz pm me or txt me on 0414424902

Thanks

Lok

hey guys n girls i have for sale: (preffer not to post but maybe able to org postage if u want to pay for it but must recieve money b4 postage)

- Garrett 3071r .86 rear .50 front

Basically brand new only been on car for dyno no shaft play/getting a TD06 25G instead

comes with lowmount manifold to suit rb25, water lines oil lines, actuator

$1900 ono ( hit me wit an offer but no low ballers plz)

- R33 front drivers and passenger seats

no rips or tears great condition

$400 ono for both

- KKR480 turbo

great condition minimal to no shaft play

$650 ono

- 5 Spoke rims suit R33 17x9.5, 17x 8.5 or 9 from jap land

bit of gutter rash (from previous owner) but other wise good condition, no tyres

$450 ono

Pictures avail on request but wll try to get it on here asap. plz pm me or txt me on 0414424902

Thanks

Lok

Hey mate,

pics of the kkr would be good. I read that thread you made about the whining noise it was making. Did you end up finding out if it was the turbo or something else?

heres pics of the KKR480. thers no shaft play at all and there was no whining noise with turbo, worked perfectly.

Cheers

Lok

post-54607-1252817352_thumb.jpg

post-54607-1252817847_thumb.jpg

post-54607-1252817887_thumb.jpg

post-54607-1252817942_thumb.jpg

yea no worries mate i want these gone so let me knw wen u can pick em up. just txt me and ill send u my address n time to pick up.

0414424902

Cheers

Lok

$65 pickup for the front seats. I can get a set of series 2 seats for $50 but have to drive 1 1/2 hrs each way to pick them up :P Thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...