Jump to content
SAU Community

Built Rb25 W26 Crank/rods/headwork/cams, Inlet Maifold And Fuel System, Are Alloy Rad And Cooler, Rb25 Box And Kit To Convert 32, Blitz Spec R Boost


Recommended Posts

Stripping out my 32 as need to get some cash together as building a house. Chassis is also for sale if you wont a good drift/track project

In Adelaide but wil ship, some parts still in car but can remove when required.

Engine: R33 RB25,2630cc?, fully built engine by Nisspeed here in Adelaide. Engine was built, engine dyno tuned and fitted in car, we used it for 12 months at about 4 drag meets and very little street use. Engine was stipped down to check it out and have a look, sump baffels were istalled, new rings and since then it has only just been started. Engine includes

RB26 crank balanced, streightened and ground

RB26 rods preped with ARP bolts

ARP cradle studs

Wiesco forged 87mm pistons

sump mods for anti oil surge

Metal head gasket

N1 oil/water pump

New thermostat

RB25 head ported

HD valve springs

HKS? 272 and 264 cams ( one was new the other as good as cant remember the exact specs)

HKS adjustable exh cam gear

ARP head studs

RB26 clear cover - modified

R33 CAS

Rocker covers painted gloss balck with -10 fittings for the breather pipes

engine does not include inlet/exh manifold/PS pump/alternator/ but can include parts if needed

Price: $5k

Inlet:

Custom inlet manifold on std runners - old Subzero type one, with 70mm? 5ltr holden throttle body

Includes alloy fuel rail with 75lb ~800cc Holley injectors

Sard pressure reg

Injectors, reg and fuel rail were new, mainfold SH but polished up

$1200

Fuel System

SX fuel pump, good for 700 HP

SX fuel filter

Alloy surge tank with pump and filter mounted on plate

Fuel cell about 30 ltr and lift pump

all conected with stainless braided teflon lines, all parts purchased new

$700

ARE cooler, 600x300x100 Bar and plate, 2.5" inlet, 3" outler,

anyone that knows ARE stuff know it is top quality, with cast end tanks for optimum flow etc, barely a mark on the cooler

$800

ARE 40mm radiator, duel pass cross flow, fits my 32, not sure if 33 etc are the same, includes large themo fan (15" ?)

$600

R33 RB25 gearbox, good contition still shifts smooth as, includes slave cyl

$1000

Conversion kit to put R33 box in R32 includes modified 1 piece tail shaft, modified gearbox mount

$100

Also have cooler piping in 2.5" and 3'' stainless, painted silver with tial BOV, and inlet pipe, 4" with big K&N filter can can include some of this if you buy multiple parts.

Blitz Duel SBC spec R boost controller, as new, $500

Dyno sheet attached of what the car did on the roller at about 1.4 bar boost

Please contact me by email [email protected]

post-429-1251959856_thumb.jpg

post-429-1251959962_thumb.jpg

post-429-1251960060_thumb.jpg

post-429-1251960105_thumb.jpg

Radiator and fuel system sold

may swap engine and or inlet setup for standard items plus cash

Sorry Chassis sold

hey mate how much u selling chassis for? defected?

Engine/Radiator/Cooler/fuel setup sold

Still have Inlet manifold with injectors and fuel reg - sard and boost controller

Will post pics in the next coupld of days now that they are out of car

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...