Jump to content
SAU Community

Recommended Posts

Boys, it is time that the r31's have a meet (although all are welcome). Rather than just a city drive, I am proposing a bit of a run down South for a bbq so we can have a chat and get to know eachother.

so here goes:

WHEN: 13 DECEMBER at 8AM (for a departure of 9am)

MEETING POINT: Caltex Service Station - Corner of Newbridge and Nuwarra Roads Moorebank

map1666.gif

WHERE TO: Jump on the motorway heading south and cruising to Kangaroo Valley.

map2.gif[/b]

WHAT'S DOING: BBQ - a chance to get to know eachother, eat some good snags, and enjoy the nice drive to the venue! It's 2 hours there, have the bbq, then 2 hours back home.

WHAT TO BRING: Your Skyline, some meat and drinks and whatever else you need to eat. We'll be stopping at grounds that have bqq facilities.

WHY YOU SHOULD COME: Sydney has a large member base of r31 Skyline enthusiasts, and so we need to get something happening. A drive day and bbq will make for a bloody good day! All are welcome though.

CONTACT: Mark on 0402 287 773.

So far the attendance is:

88SILHOUETTE

REDX

ALAN (MATE OF OURS)

ALLIANCE_22

AMPHO'S WAGGIN

RICKY_B

R324D and mate (from skylines australia forums)

Let's make this one a ripper boys!

Link to comment
https://www.sau.com.au/forums/topic/28863-dec-13-sydney-meet-and-bbq/
Share on other sites

Hey

Sounds like it would be a good day! I should be there...  

My mate has just got his car back on the road Rx7 series 5, hmmm just finished his 10 second package...  

anyone mind if a rotor is amongst the crowd?

of course your mate is welcome.

anyone is welcome (we do love nissans though! hehe) provided they aren't dicks.

see ya there mate, MARK



  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...