Jump to content
SAU Community

Recommended Posts

Hey everyone

Im selling the complete interior from my series II R33 GTST.

The reason for sale is i have stripped it out for track use and do not need it anymore.

Pics and prices are as follows, prices are negotiable.

0418 440 422

[email protected] (prefered)

Location is Sydney

Series 1 grille charcoal gc $80

Headliner gc $150

Full carpet (has been cut but will be hidden by console and dash, no rips) $150

A/c control gc $120

Dash pocket (opening and closing door) vgc $80

Front ash tray, like new never used $60

Rear ash tray , vgc $15

Drivers A pillar trim vgc $100

Passengers A pillar trim vgc $80

Drivers Rear window cpillar trim $130

Passengers rear window c pillar trim $130

drivers rear side trim vgc $100

passengers rear side trim $100

complete boot trim $200

standard turbo back exhaust with small canon muffler $250

Drivers Rear seat belt and buckle $100

Passengers Rear seat belt and buckle $100

Centre Rear seat belt and buckle $100

Front interior light assy $30

Rear interior light assy $30

Clock $50

Rear seats gc (need a clean) $300

A/c Vents $40 each

Complete Factory Intercooler with hoses, brackets and bolts $200

OR $1600 for the lot

Thanks, Dave

post-53643-1253776681_thumb.jpg

post-53643-1253776695_thumb.jpg

post-53643-1253777419_thumb.jpg

Edited by DVSZED
do you have standard cat?

good nick?

how much?

Hey mate

I have the standard cat in good working order as far as i can tell, included with the standard system for $250

would prefer to sell as one but for cat alone $100.

Dave

Hey mate

I have the standard cat in good working order as far as i can tell, included with the standard system for $250

would prefer to sell as one but for cat alone $100.

Dave

i also have a near new high flow cat that you can have for $220

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ha, I've never pressed the X in all these years incase it removed the notification for all Admins
    • I don't know, I've never done it that way, but 1. While it is an interference engine, there is still clearance between the valves and the piston at all points in the regular timing cycle 2. There is not a lot of distance before you can't catch the top of the valve stem any more I don't know if 2 is greater or less than 1. But 3. If it doesn't work out you are f**ked, engine is coming out to disassemble so it is a big bet.
    • Semi slicks are horrible for road use, just use a high performance road tyre unless you really need the maximum grip. Noisy, unpredictable (amazing, until they are not), expensive due to very high wear and not good in cold and particular wet. And yes, it is a thing to store cars on stands instead of tyres if you know they are going to be parked up long term.....but who ever realises that a short park is going to stretch into years before it is out again!
    • I know in Australia you'll definitely get above 30c. Parked in the shade in Summer you'll be above that. 😛 But in cooler climates, you might get that warm driving on the highway for a bit, but you'd never get to full heat temp. I'll try and find some of my historical tyre temps between Aus summer and winter (be aware immin the warmer area of Aus too.)
    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
×
×
  • Create New...