Jump to content
SAU Community

Recommended Posts

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Sounds good, what did u have in mind?

hey was wondering who has a banner for the club etc? for the display, would be nice to make it look all official.

I believe I'll be collecting the banner for the Loxton Show ... and then bringing it to the EHP show ... so may be the holder of it come the Mallanats.

I'm keen for the show and shine and the cruise ... maybe dyno too :dry:

id be keen on the show n shine although my cars pretty stock exept a gtr bodykit and 19s but would be good to meet a few of u guys as im new on here lol.

Edited by my33gtst
A cruse up would be killa to i recon. somewhere central on the way like city dismantles or something.

yep, im up for that..

i live up around gawler somewhere :D

but im not fussed about driving down to city dismantlers or soemthing like that then cruise up to mallala.

be up for the show and shine, and the track cruise too.

  • 3 weeks later...

I'm not entering anymore, I'll go and watch the 1st one. Maybe next time. I've got a feeling that the organisers are gonna be a bit anal with everything. Also, It starts at 11am till night time. That's gonna be a full-on day. Everything's gonna be rushed. But hopefully it works, if so, I'll definately be there at the next one!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...