Jump to content
SAU Community

R33 Front Camber

prescott06
 Share

Recommended Posts

prescott06 Community Regular

prescott06

Posted
Posted

So I recently bought a S1 R33 Gtst. First thing I did was take it for a wheel alignment as it was pulling left considerably.

Everything was adjusted fine, apart from the front right camber is at -3.4 degrees or so.

I can't see anything obviously bent. Without pulling all the arms out and comparing side to side, are there some measurements I should be taking?

If its a case of throwing a pair of adjustable upper arms on, are the Cusco items the ones to go for? Would the Just Jap ones be worth considering, given that this car is my daily driver?

Link to comment
https://www.sau.com.au/forums/topic/291594-r33-front-camber/
Share on other sites
_Ryan_ Grand Master

_Ryan_

Posted
Posted

two kits? i thought it was closer to 2deg, that might be R32 though... i know my stagea has ~ -1.5deg from one kit same as the 33 kit

noltec make an arm with bushed ends IIRC... that would be my next choice

ssxRicho Grand Master

ssxRicho

Posted
Posted

-3.4 is heaps on stock bushes....

how low is it? from guard to center of hub.

mine is too low atm, 340mm, which should mean that i've got camber on tap. but -2.5 is my max with pedders camber bolts.

im running -2 on a track based setup.

JSTA33 Rising Star

JSTA33

Posted
Posted

is there a way to adjust stock front camber? i get pretty bad inner tire wear on both fronts, (backs are perfectly fine)..

or do i need a adjustable camber kit? i need to either bring the bottom of the wheel in or push the top of the wheel out.

my radius rod bushes are gone, which im replacing, so might that contribute to it?

evil_weevil Grand Master

evil_weevil

Posted
Posted

wow that is alot of camber.

I had -4 in my r33 but I had modified front lower arms which pushed it to -4 with whiteline camber bushes.

beforte that I could get JUST to -2

Something may be bent down there...or perhaps previous owner did something like I had :P

prescott06 Community Regular

prescott06

Posted
  • Author
Posted

Yeh, something is not right at all. Had a quick look before, but couldn't see much. I need to get the tape measure out before I start buying arms i think :P

If the previous owner did do something, they were pretty dumb to only to it to one side :)

  • 1 month later...
prescott06 Community Regular

prescott06

Posted
  • Author
Posted

So I think I have this problem figured out.

I measured all the arms, and none of them are bent. What is bent though is the front bolt holding the upper control arm to the car.

Hopefully replacing this bolt and getting a set of the whiteline eccentric bushes should sort out my problems :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...