Jump to content
SAU Community

Removing Strut Bar

Hanaldo

By Hanaldo,
in Western Australia

 Share

Recommended Posts

Tony de Wonderful Veteran

Tony de Wonderful

Posted
Posted
it is simple physics really i would draw you all a picture but should not have to explain myself. if you notice as you raise and lower a car your wheels will move in and out slightly this is the pressure i am refering to on the strut. do any of you back yard mechnics do things the correct way or just bach things out?

As I understand it the strut should neither be in tension nor compression with the car on the ground 'doing nothing'. Ergo, if you remove the bar it would make no difference to the 'sag' (if you like) between the two towers and so your (effective) alignment would be the same.

OTOH if you put your bar on with the car jacked up, the bar would be in some compression when the car is back on the ground, and yep removing the bar would change the (effective) alignment. By how much I dunno. Probably negligible.

NISMOGTT Collaborator

NISMOGTT

Posted
Posted (edited)
As I understand it the strut should neither be in tension nor compression with the car on the ground 'doing nothing'. Ergo, if you remove the bar it would make no difference to the 'sag' (if you like) between the two towers and so your (effective) alignment would be the same.

OTOH if you put your bar on with the car jacked up, the bar would be in some compression when the car is back on the ground, and yep removing the bar would change the (effective) alignment. By how much I dunno. Probably negligible.

you are correct with your first comment if there is no camber and the car is on flat ground... but i also said do not take the tyres off the ground just the weight off them, also the strut will be under slight tension or compression that is the reason for the adjustment bolt on the bar... we dont know how tight or loose his adjustment is unless you have seen the car.

post-41866-1255590056_thumb.jpg

i was trying to give some easy tips rather then just bash it off or get bigger muscles. i would hate to see some of the repairs (botch jobs) done on some of these guys cars.

Edited by NISMOGTT
Hanaldo Grand Master

Hanaldo

Posted
  • Author
Posted

Lol well to make sure its sharp im testing it out on your brake lines k :P

None of these suggestions have worked by the way... Gonna take it to my mechanic tomorrow, he might give it a go with the rattle gun. Turns out they are on there really tight, its ridiculous. I may have to paint it with it on the car, but thats worst case scenario because it should be able to come off

R34 Mentor

R34

Posted
Posted
Lol never thought this question would be the cause for such a big argument. All i want is to get my strut bar off haha

Sorry for hijacking Martin

If you're still having dificulties and are NOR shoot me a PM and I'll come and help you

Yaah31 Collaborator

Yaah31

Posted
Posted (edited)

yea nice man they stand out red dont they ! , thats why i did mine , but yea looks good man

oh yea btw i dont even remebver u having a strut bar on ur yah34 dealy in the first place did u like all of a sudden put me in ? lol , when we where putting my heat shield in ur car i dont remeber it lol , but yea cutting disc XD , AND NO NOT ON MY BRAKE LINES :D

Edited by Yaah31

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...