Jump to content
SAU Community

Anz Ghost 18" Rims With Tyres & R34 Bumpers - Melb

DriftinThruLife
 Share

Recommended Posts

DriftinThruLife Enthusiast

DriftinThruLife

Posted
Posted (edited)

Hi Folks.

Selling

1) a set of 4 ANZ Ghost Rims with Tyres.

They are 5 stud multifit (5x114.3 and i think 5x100). They look really nice in person. I will include the nuts to go with them. The tyres are nexen 235/45/18 80%+ tread.

Asking $900

The bumpers have some scratches/scuffs on them, but should come out when prepping/priming etc

2) Standard R34 front bumper (silver). Has a small section of the bottom back part cut out to fit the intercooler piping. Asking $100

3) Standard R34 rear bumper (silver). Has the "Skyline" badge/word on it. Asking $100

4) In the near future....Will be selling my r34 GTT stock wheels with tyres (tyres have wear on the insides). Asking..... EOI?

-----------------------------

http

:thumbsup: /cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...STRK:MESELX:IT

Edited by DriftinThruLife
  • 3 weeks later...
  • 3 weeks later...
Talon88 Apprentice

Talon88

Posted
Posted

Selling

1) a set of 4 ANZ Ghost Rims with Tyres.

They are 5 stud multifit (5x114.3 and i think 5x100). They look really nice in person. I will include the nuts to go with them.

The tyres are nexen 235/45/18 80%+ tread.

Asking $900

--------------------------------------------------------------------------------------------

hey man

are u still selling them? and are they 18"?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...