Jump to content
SAU Community

Black R32gtst - Sydney

BLACK_Rb20
 Share

Recommended Posts

BLACK_Rb20 Rookie

BLACK_Rb20

Posted
Posted (edited)

I have for sale a Black, manual R32 GTS-T 1990. 103000K's on the Clock.

It drives nicely and is a firm ride with the Nismo setup. 100,000k service was done at 82000k. This included Timing belt, waterpump, thermostat, seals changed. Also recently (as I replaced the spark plugs to the copper iridiums) I have done a compression test and all the cylinders fall between 150-160psi.

The Oil (Penrite) and Oil filter (Genuine Nissan) is always changed every 5000ks. Fuel Filter changed every 15000ks. The O2 sensor has been replaced 25000k's ago. Always use BP Ultimate fuel. Car is garaged most of the time.

The Mods include:

- Apexi POD Filter

- ARC Intercooler

- AVCR Electronic Boost Controller

- Nismo shocks and spring package

- Front Eurothane Caster Rod bushes

- Strut Brace

- Mines ECU

- Slotted Front Rotors

- 3 Inch Cat Back – Exhaust

- 19 Inch Rims with Federal Tires all round

Interior

- Pioneer Headunit with remote control

- 6.5" Split Front Speakers

- Blue Neons under footwells (Turns on and off automatically when the door open/closes).

- Mongoose 3 Star Immobiliser alarm – Keyless entry

I'm after $9500k ONO as is. If you are serious in looking for a decent r32, I suggest you look at the others in the market and then afterwards come see mine.

I'm located near Surry Hills. PM me if you are interested and we can arrange a viewing.

Andy

post-68050-1257318116_thumb.jpg

post-68050-1257318147_thumb.jpg

post-68050-1257318179_thumb.jpg

Edited by BLACK_Rb20
Link to comment
https://www.sau.com.au/forums/topic/294827-black-r32gtst-sydney/
Share on other sites
  • 2 weeks later...
  • 4 weeks later...
  • 1 month later...
  • 4 weeks later...
  • 2 months later...
Owens Rising Star

Owens

Posted
Posted

hey,

I am interested in your car. I would have PM'ed you but I dont have enough posts yet. I have a honda prelude so usually post on prelude australia forums lol.

I would like to know a couple things first though..

Have you ever got it dyno tuned before? And if so what power did it put out?

It looks very neat and clean. Was wondering if you had any pictures of the interior and seats though?

Think it would be possible if I could come up this week and inspect it? I live down in Wollongong.

Let me know :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...