Jump to content
SAU Community

Water Temp, Oil Press, Volt Meter Gauges (sard Style)


Recommended Posts

Hi recently I just came back from foreign country and bought some SARD Style Gauges.

These gauges are all new, they are replicas but work great, come with boxes.

The rear is cleaner than most gauges with just wires coming out from one hole

Size is 2.625" (66.675mm) -I have attached a flybuy card as reference

(wanted to install them in my car but realised I only do daily driving so..)

Location: Brisbane city, West End near Coles [Pick Up anytime day/night]

Contact: 0410 139 151 (TXT) [JS]

Pictures and Price

===================

Water Temp Gauge [$70] - cold start monitor, important for mountain driving

http://img4.imageshack.us/img4/1605/watert...rontandrear.jpg

watertempfrontandrear.th.jpg

Water Temp Sensor connector/Piping for Radiator hose [$25]

http://img40.imageshack.us/img40/5163/watertemppipe.jpg

watertemppipe.th.jpg

Oil Pressure Gauge [$75] - important for drag race to prevent engine rebuild (if oil press decrease when drag/accelerating, time to slow down!!]

http://img35.imageshack.us/img35/1836/oilp...rontandrear.jpg

oilpressfrontandrear.th.jpg

Voltage Meter Gauge [$70] - monitor battery condition, below 11 means time to switch battery (14 is good enough)

http://img35.imageshack.us/img35/3900/voltsfrontrear.jpg

voltsfrontrear.th.jpg

Stands (total 3), each [$20] - rear of all gauges are clean, so no cup is required!

http://img4.imageshack.us/img4/453/standf.jpg

standf.th.jpg

Sample pic when light is on - this one is mounted on steering holder on my 4WD.

http://img697.imageshack.us/img697/2672/lighton.jpg

lighton.th.jpg

no one is interested?

i posted this on boostcruising as well, and a few are eyeing the volt gauge and and water temp

anyone is interested in the oil pressure gauge?



  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...