Jump to content
SAU Community

Recommended Posts

PM FOR PICS OR CALL, MATT:0448887446 IF YOU HAVE ANY QUESTIONS, Most parts are still in vehicle but will be removed over the next couple of weeks

#ENGINE AND PARTS REQUIRED FOR A PROVEN 180KWATW+ CAN BE PURCHASED AS A PACKAGE IF REQUIRED(engine, ecu, turbo, injectors, intercooler, plumbing, BOV, fuel pressure reg, K&N Filter, braided fuel lines and fittings, remote filter mount and lines, oil cooler and lines) FOR $3000#

Evo/VR4 Twin spot Front Brake calipers, ADR braided lines, Evo RDA slotted rotors

(redrilled to 4x100 for lancer/mirage), Project MU type hc+ Pads: $400

Proton Rear Disc Brake conversion for lancer/mirage, Bendix Ultimate pads, ADR braided lines: $300

Mirage Whiteline Rear Sway Bar: $100

HKS Intercooler: $200

Intercooler Plumbing: $100

Haltech E6X ECU with GSR/EVO Adaptor Loom: $700

4 x R34 GTR Injectors: $200

Turbosmart StreetReg Fuel Press Reg.: $200

Evo 3 TD05-16G Turbo(bought new from ATS): $500

Toyo R888 15"Semi Slicks(Only 2 Hillclimbs old): $600

Toyo RS-1 15" Slicks(Only did 1 Time Attack): $700

Work Emotion CR 15" Alloy Wheels(new only 3 months ago): $800

CE Mirage/Lancer Ksport Coilovers(not even 12 months old): $700

Evo 2/3 Gearbox with Mech Front Diff (Rebuilt by CVAP Prior to purchasing): $1500

VL Turbo Fuel Pump: $50

Momo Safari Race Seat (Black): $500

CE Mirage Bolt in Half Roll Cage: $500

CC GSR 4G93T Engine: $900

Evo 1" Brake Master Cylinder: $100

Remote filter Mount+cooler & Earls Lines and fittings: $300

K&N Pod Filter: $25

Oil Catch Can: $50

Greddy Profec B Boost Controller: $300

CC 1.8lt Extreme Button Clutch: $100

Coolant res.: $50

HKS BOV: $100

CC GSR Driveshafts: $100

Cordia LH Driveshaft: $50

CC Coupe Driveshafts: $50

Toyo R888 15"Semi Slicks(Only 2 Hillclimbs old): $600

Toyo RS-1 15" Slicks(Only did 1 Time Attack): $700

Work Emotion CR 15" Alloy Wheels(new only 3 months ago): $800

Can you be more specific on the tyre and wheels sizes? eg 195/50/15 15"x7" +20 wheels. Also how much tread is left other than 2 hillclimbs?

Whereabouts are you?

Cheers.

Sorry about that fellas.

All Parts are located in Adelaide

Toyo r888 205/50/15 approx. 70%+ tread left(cost $300+ each new)

Toyo RS-1 2x205/50/15 approx. 60%+ tread left and 2x195/50/15 approx. 80% tread left(cost $400+ new each)

Work Emotion CR rims are 15x7" +44 offset

Yes it is true, the car was on the market and hasn't sold as a whole, now it will be returned to a street car and all performance parts sold off. Need to move to make way for new project

Edited by no grip mirage
  • 1 month later...
Evo/VR4 Twin spot Front Brake calipers, ADR braided lines, Evo RDA slotted rotors

(redrilled to 4x100 for lancer/mirage), Project MU type hc+ Pads: $400

Proton Rear Disc Brake conversion for lancer/mirage, Bendix Ultimate pads, ADR braided lines: $300

Evo 1" Brake Master Cylinder: $100

whats the best price you would do for all these?

PM me if you wish :down:

front brakes and master cylinder are sold, you can have the rear disc brake conversion for $250 if your interested

interested !

what would i be looking at for postage to Mt Pleasant 6153 (WA)

interested !

what would i be looking at for postage to Mt Pleasant 6153 (WA)

not sure, will put items on a half pallet, but you will need to organise your transport. Sold a gearbox to a fella in Perth, cost him $60 to get it there.

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...