Jump to content
SAU Community

Recommended Posts

Hi Guys,

Got some tyres and wheels I'd like to get rid of so here they are:

1. 4x Stagea rims/BBS forged rims 16inch - $120

My mate used the two rims with legal tyres to pass a blue slip on his S15. Will fit anything with a 5x114.3 (R33's may need a little spacer on the front to clear brakes)

Two good tyres (retreads) and two tyres which may or may not be just legal.

post-28122-1260277544_thumb.jpg post-28122-1260277588_thumb.jpg post-28122-1260277672_thumb.jpg

2. 4x Kosei Japanese rims light weight. front 17x8 rear 17x9 with tyres, but bald - $220

These rims came with my skyline from japan, they are very lightweight, few marks on them. 114.3x5 doesn't say offset, but Im guessing around +38 Sat flush on r33 with 2-3mil spacers.

post-28122-1260278150_thumb.jpg post-28122-1260278244_thumb.jpg

3. Aristo stock wheels 16x7.5 front 16.8.5 rear, tyres are on the markers, one has bad camber wear. Will fit vehicles with 5x114.3 - $140

These are off my aristo, tyres probably suit drifting or burnout tyres. Without centre caps, these wouldn't look to bad on a r32.

post-28122-1260278594_thumb.jpg post-28122-1260278642_thumb.jpg

4. R32 stock rim - legal tread $40

Good for a spare..

post-28122-1260278877_thumb.jpg

5. 17inch bridgestone tyre legal tread 225/45 $50

post-28122-1260278958_thumb.jpg

that's it fellas, priced them cheap for a quick sale.

Contact; pm me for my number.

Located in Sydney's West.

Cheers'

Daniel

Hi mate, i'm interested in the rims listed below.

2. 4x Kosei Japanese rims light weight. front 17x8 rear 17x9 with tyres, but bald - $220

These rims came with my skyline from japan, they are very lightweight, few marks on them. 114.3x5 doesn't say offset, but Im guessing around +38 Sat flush on r33 with 2-3mil spacers.

What part of sydney are you located and are they available to be picked up friday?

thanks

Hey guys, just realised the Kosei rims do have an offset on the back, its +45..

Sorry to the guy who came and looked at them..

They sat good on a r33 with 2-3mil spacers..they might fit without spacers too.

hey mate whats the offset on the stagea 16's?

Hi Guys,

Got some tyres and wheels I'd like to get rid of so here they are:

1. 4x Stagea rims/BBS forged rims 16inch - $120

My mate used the two rims with legal tyres to pass a blue slip on his S15. Will fit anything with a 5x114.3 (R33's may need a little spacer on the front to clear brakes)

Two good tyres (retreads) and two tyres which may or may not be just legal.

post-28122-1260277544_thumb.jpg post-28122-1260277588_thumb.jpg post-28122-1260277672_thumb.jpg

2. 4x Kosei Japanese rims light weight. front 17x8 rear 17x9 with tyres, but bald - $220

These rims came with my skyline from japan, they are very lightweight, few marks on them. 114.3x5 doesn't say offset, but Im guessing around +38 Sat flush on r33 with 2-3mil spacers.

post-28122-1260278150_thumb.jpg post-28122-1260278244_thumb.jpg

3. Aristo stock wheels 16x7.5 front 16.8.5 rear, tyres are on the markers, one has bad camber wear. Will fit vehicles with 5x114.3 - $140

These are off my aristo, tyres probably suit drifting or burnout tyres. Without centre caps, these wouldn't look to bad on a r32.

post-28122-1260278594_thumb.jpg post-28122-1260278642_thumb.jpg

4. R32 stock rim - legal tread $40

Good for a spare..

post-28122-1260278877_thumb.jpg

5. 17inch bridgestone tyre legal tread 225/45 $50

post-28122-1260278958_thumb.jpg

that's it fellas, priced them cheap for a quick sale.

Contact; pm me for my number.

Located in Sydney's West.

Cheers'

Daniel

Is the R32 rim off a GTR or GTS-T ??

Not sure if they are different offsets or not ??

I have a set of GTR wheels on my trailer and would need the same offset to suit as a spare.

Thanks.

Is the R32 rim off a GTR or GTS-T ??

Not sure if they are different offsets or not ??

I have a set of GTR wheels on my trailer and would need the same offset to suit as a spare.

Thanks.

Hi Mate,

not 100% sure, but I think the gtr wheel is 1inch wider??? and I am guessing the offset is not the same.

Cheers

Daniel

Thanks for responding.

I should've asked if you could check the wheel.

On the outside of the wheel, the size & offset is stamped between the stud holes and centre.

It should be (from memory) 16x8jj+30 I think ??

Caould you check please.

Thanks.

Thanks for responding.

I should've asked if you could check the wheel.

On the outside of the wheel, the size & offset is stamped between the stud holes and centre.

It should be (from memory) 16x8jj+30 I think ??

Caould you check please.

Thanks.

sorry mate, didn't have anything printed that looked like an offset???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...