Jump to content
SAU Community

Recommended Posts

once again, these are up for sale. got hella interest. but no ones fronted the cash (most promising offer would make most lowballers cringe).

work mesh, 17x8 +5 and 17x9 +11. fronts are straight 5x114, rears are multifit 4/5x114.

bit of kerbage on them, but you have to be looking pretty close. the worst of them was one of the 9's which had a slight dent in the outer hoop which has recently been repaired.

and some of the clearcoat is starting to peel around the hubs, but overall, theyre in pretty rad condition.

4902P5120746.jpg

IMG_3157.jpg

taking offers around $1500 without tyres. offers lower than $1400 will be laughed at, and responded to in kind.

contact me (dave) on here or on 0408961657.

can send interstate if needed, but id rather not.

if you dont shit me off within 4 seconds, i might even be able to arrange a payment plan.

Link to comment
https://www.sau.com.au/forums/topic/300557-sa-17-inch-work-mesh-wheels/
Share on other sites

  • 2 weeks later...
ugh, bump again. gotta be some interest out there.

What rubber is on them ? Brand/sizes ? Just to get this right........ +5 multi stud on rear ? SO +11 BEING THE 9" and larger width wheel,

is on front ? Cheers MIKE

i got interest in the bump photo bro :rofl: haha what other wheels you bought?

lol, f**kin rad bump pic eh?

havent bought wheels yet. but im looking at cts's, 17 x 9.5 +15 all round.

What rubber is on them ? Brand/sizes ? Just to get this right........ +5 multi stud on rear ? SO +11 BEING THE 9" and larger width wheel,

is on front ? Cheers MIKE

225/45/17 Kumho Ku36's on the front (f**kin sticky), and 215/45/17 Kumho Ku25's on the rear.

the fronts are 17x8 +5, rears are multistud's and 17x9 +11.

ive had about a half a dozen people say that, and my reply has been the following.

im not splitting. you either buy all 4, or you dont buy them at all.

ive had about a half a dozen people say that, and my reply has been the following.

im not splitting. you either buy all 4, or you dont buy them at all.

Why not say, sure, for $1500 and I'll chuck in two fronts for zip!

:banana:

If I had $1500 blowing a hole in my pocket I'd snap em up (too bad I'm post-wedding broke ATM)

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

Why not say, sure, for $1500 and I'll chuck in two fronts for zip!

lol, ive said that once aswell.

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

CoolStoryBro.jpg

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

sounds like your polishing more than your wheels there frenchy

bump to the top for some tough,well priced rims and tyres

deposit received.

lol then if you wont split, you never gonna sell these wheels, well njot at that price, i just bought a full set that had just been re rolled and polished with tires for $900...

... you were saying?

:D

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
×
×
  • Create New...