Jump to content
SAU Community

shutokou toraiaru

MINES_DATSUN

By MINES_DATSUN,
in General Automotive Discussion

 Share

Recommended Posts

(B1) MR_fanny Grand Master

(B1) MR_fanny

Posted
Posted

is that that shuto trial movie thingy?? if it is well u can find it at any good vcd store. theres 3 parts i think..though i only found the one with the r33 to be decent to watch. its too typical japanese acting(corny) and the other part was like it was made in 1989 when the r32gtr came out but its actually part 2 of the series...go figure. it was crap!! so i didnt bother borrowin part 3.

Link to comment
https://www.sau.com.au/forums/topic/30146-shutokou-toraiaru/#findComment-612982
Share on other sites
Bakadesu! Contributor

Bakadesu!

Posted
Posted

Well I'm not in Japan right now, but I've seen it. :)

Shutokou Trial is basically about a bloke trying to become the king of streetracers, but is haunted by the fatal crash of his best mate, which he feels guilty for etc...

The story kinda (very) boring, but the freeway action is of cool, and it's fun to see an R33 GTR drifting around mountain roads, and on the track.

You might be able to find a legitimate VCD release of it somewhere here...Chinatown maybe.

Link to comment
https://www.sau.com.au/forums/topic/30146-shutokou-toraiaru/#findComment-612987
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • r32-25t
      R32 gtr transmission strength, billet plate

      By r32-25t · Posted

      Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...