Jump to content
SAU Community

Recommended Posts

Forsale

Black lenso 17's 4x114.3 comes with spacers. $700

To4e turbo had it on car no problems minimal shaft play came on hard. $300

S13 cusco coilovers $200

Rb20 silvertop turbo good condition comes with mani, 3inch dump pipe, induction hose ready to go $400

Rb20 silvertop injectors $100

Rb20 AFM green lable $80

Turbosmart Vee-port BOV $100

R31 handbrake assembly $100

Import struts comes with control arms, disk, calipers, springs, hubs all bolts $500

ALL ITEMS IN GOOD CONDITION

Pm me. Parts located in sydney inner west can post small items

Pictures will be up tonight.

Link to comment
https://www.sau.com.au/forums/topic/306819-r31-rb20-rb25-wheels-coilovers/
Share on other sites

Forsale

Black lenso 17's 4x114.3 comes with spacers. $700

To4e turbo had it on car no problems minimal shaft play came on hard. $300

S13 cusco coilovers $200

Rb20 silvertop turbo good condition comes with mani, 3inch dump pipe, induction hose ready to go $400

Rb20 silvertop injectors $100

Rb20 AFM green lable $80

Turbosmart Vee-port BOV $100

R31 handbrake assembly $100

Import struts comes with control arms, disk, calipers, springs, hubs all bolts $500

ALL ITEMS IN GOOD CONDITION

Pm me. Parts located in sydney inner west can post small items

Pictures will be up tonight.

post-67045-1265274729_thumb.jpg

post-67045-1265274741_thumb.jpg

post-67045-1265274750_thumb.jpg

post-67045-1265274760_thumb.jpg

post-67045-1265274771_thumb.jpg

post-67045-1265274783_thumb.jpg

post-67045-1265274802_thumb.jpg

Also i have a koya drifttek rim in black 5x114.3 good nick without tyre $200 or swap for same rim but in 4x114.3

Edited by mattie09
hey mate basically bolt it to the flange, block coolant lines, reconect oil sup. oil drain. n Vband clamp it up, i gave a few spare clamps around u can have.
Forsale

Black lenso 17's 4x114.3 comes with spacers. $700

To4e turbo had it on car no problems minimal shaft play came on hard. $300

S13 cusco coilovers $200

Rb20 silvertop turbo good condition comes with mani, 3inch dump pipe, induction hose ready to go $400

Rb20 silvertop injectors $100

Rb20 AFM green lable $80

Turbosmart Vee-port BOV $100

R31 handbrake assembly $100

Import struts comes with control arms, disk, calipers, springs, hubs all bolts $500

R31 front and rear struts with pedders springs, disk and calipers new pads allround, control arms with new bushes $250

ALL ITEMS IN GOOD CONDITION

Pm me. Parts located in sydney inner west can post small items

Pictures will be up tonight.

hey mate The comp. inlet measures 65mm the turbo has no markings on it. but the housings are big had it on a rb20 came on spastic 2nd 3rd 4th.

  • 3 weeks later...
  • 3 weeks later...
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...