Jump to content
SAU Community

Recommended Posts

Hi Guys,

These rims are discontinued now, so grab this oportunity to own a rare set of Rays. These will fit most skylines (not GTR), hondas, mitsubishi,STI (5x114.3)...

Size: 19x8.5

Offset: +40

Condition: No gutter marks, only a few stone chips here and there on the spokes

101_1202.jpg

101_1203.jpg

101_1204.jpg

Link to comment
https://www.sau.com.au/forums/topic/306842-rays-99b-19x8540-2200/
Share on other sites

Are you sure it was a option? Did you buy the wheels new?

Cheers

Dude, i'm a vendor and these were traded in. All Rays wheels when bought new don't come with centre caps and nuts. We deal direct we Rays so yes i'm sure. These wheels are secondhand, if bought new they are $3500+

Sorry Dude but the only reason why I asked is, a friend of mine bought 99B for his 32GTR and The 08-09 RAYS catalogue states that the following items are inlcuded. Valvestems, Center cap, and Long adapter + 17 HEX Nut set.

Sorry Dude but the only reason why I asked is, a friend of mine bought 99B for his 32GTR and The 08-09 RAYS catalogue states that the following items are inlcuded. Valvestems, Center cap, and Long adapter + 17 HEX Nut set.

Mate, not sure which Rays catalogue he had but i've never seen Rays giving out lugs nuts ever. Valve stem and caps are with these wheels as pictured. Show me the Rays catalogue that has it and i'll chuck in the Mcgards nuts for free!!!

with all rays wheels, the centre caps and lug nuts are opitional....

they have to be purchased onto of the wheel..

I have bought 3 sets of Rays wheels and never ever have they come for free

Hope this clears up any mistakes

GTR32X and OTR take a closer look at the catalogue picture I sent you. Does it look like a mistake?

I stand corrected, but this is secondhand and you have no interest in buying so why bother debating over something you don't intend to buy?

SOLD ANYWAYS



  • Similar Content

  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...