Jump to content
SAU Community

Recommended Posts

Expression of Interest

1995 R33 GTS25T S1.5 RB25DET - 123K kms (services 600kms ago with Motul 300v Chrono motorsport oil).

5 speed manual

White

Rego till April

- Trust Greddy Turn Flow FM FMIC (uses factory piping)

- HKS 2540 turbo (240rwkw at 1.2Bar. Driven at 0.6 bar)

- Bosch 044 Fuel Pump

- Malpasi Fuel Regulator

- Hi Flowed Factory Injectors

- Cooling Pro Alloy Radiator (52mm)

- Exedy Cushioned Button Clutch

- Apexi AVCR Electronic Boost Controller

- 3" RSR Catback Exhaust with dump/front pipe

- Garage Saurus Chipped ECU from Japan

- F17x8 +30 R17x9+35 Work Meister S1 2 Piece Rims (white) 245/40/17 KU31 tyres all round.

- R33 GTR rear Sway Bar (27mm)

- D1 Spec Oil Catch Can

- Front Strut Brace

- Z32 Air flow meter

- Bilstein Coilovers

- JVC MP3 head unit with Bilken Ipod caple

- Fusion 6x9

- Nismo Side indicators

- Mspec kit (front, side and rear pods)

- 15% tints all round

- Metal Intake Pipe with Pod (not installed)

Reason for sale: I need a daily driver for work because my student card will finish in march and my public transport bill will double (hence it will be cheaper to drive).

BTW this is just an expression of interest because i havnt had this car for all that long and i love it so its not an easy decision.

17465_213498005884_629240884_3140514_3300072_n.jpg

18865_225351970884_629240884_3196349_4761690_n.jpg

IMG_0339.jpg

21065_301898485884_629240884_3505658_6417015_n.jpg

Price: $13,900 with Meisters or $12,00 BYO wheels.

Willing to trade but i dont want a high powered fuel guzzling machine.

Contact via Pm please

  • 2 weeks later...
BUMP

Willing to trade for good condition Mx5!!

BUMP

Car is now fitted with hicas lock bar - new rear break discs and machined front discs - Bendix Ultimate pads all round - Clutch has been adjusted so all good - new D1 hicas boss kit and JJR drift 350mm deep dish steering wheel in seude - new airbag wiring unit and horn wires

all this and the price is still the same!!!

IMG_1286.jpg

26046_327281410884_629240884_3585017_3711487_n.jpg

Edited by ahmad

New mods:

- Greddy Full Auto Turbo Timer

- Hicas removal/lock bar

- Bendix Ultimate brake pads all round

- HKB Hicas boss kit + JJR Dirft style deep dish 350mm steering wheel

- 1kg Fireextinguisher mounting kit

- D1 Spec light weight Lug Nuts (long version) Blue

- 15% tints all round

- Metal Intake Pipe with Pod (not installed)

- 3 inch decat pipe (not installed)

MOD LIST UPDATED

BIG PRICE DROP - I'VE FOUND SOMETHING I WANT AND DONT WANT TO MISS OUT BEFORE MARCH WHEN MY STUDENT CARD EXPIRES

NOW ONLY 12,400 OR 10,500 BYO WHEELS

Now comes with plates RB10VE

Don't know what else someone would want, there is enough parts on there to get what I'm asking for, if it doesn't sell soon I'll be parting it out.

All good dudes

Another price drop

PRICE DROP $12,000 NEG OR $10,100 BYO WHEELS???

THROW ME SOME OFFERS, YOU MAY GET LUCKY

I dont know how to edit the first post---- how do i edit the first post?

if by late march this car isnt sold - itll will be torn apart and sold bit by bit - im just lazy

Really, noone is interested in this???

I've found a mx5 down the coast and it's exactly what I want.

So pretty much, any offer is a good offer and will be considered.

PRICE DROP!!!! NOW $11,500 AS IS $9,600 without wheels!!!!!!

I dont know what else you want!!!! come on

EDIT: Can a mod please change the title to :

URGENT SALE: 1995 Nissan Skyline R33 S1.5 Mspec

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, that is it! It is a pretty expensive process with the ATF costing 50-100 per 5 litres, and a mechanic will probably charge plenty because they don't want to do it. Still, considering how dirty my fluid was at 120,000klm I think it would be worth doing more like every 80,000 to keep the trans happy, they are very expensive to replace. The job is not that hard if you have the specialist tools so you can save a bit of money and do it yourself!
    • OK, onto filling. So I don't really have any pics, but will describe the process as best I can. The USDM workshop manual also covers it from TM-285 onwards. First, make sure the drain plug (17mm) is snug. Not too tight yet because it is coming off again. Note it does have a copper washer that you could replace or anneal (heat up with a blow torch) to seal nicely. Remove the fill plug, which has an inhex (I think it was 6mm but didn't check). Then, screw in the fill fitting, making sure it has a suitable o-ring (mine came without but I think it is meant to be supplied). It is important that you only screw it in hand tight. I didn't get a good pic of it, but the fill plug leads to a tube about 70mm long inside the transmission. This sets the factory level for fluid in the trans (above the join line for the pan!) and will take about 3l to fill. You then need to connect your fluid pump to the fitting via a hose, and pump in whatever amount of fluid you removed (maybe 3 litres, in my case 7 litres). If you put in more than 3l, it will spill out when you remove the fitting, so do quickly and with a drain pan underneath. Once you have pumped in the required amount of clean ATF, you start the engine and run it for 3 minutes to let the fluid circulate. Don't run it longer and if possible check the fluid temp is under 40oC (Ecutek shows Auto Trans Fluid temp now, or you could use an infrared temp gun on the bottom of the pan). The manual stresses the bit about fluid temperature because it expands when hot an might result in an underfil. So from here, the factory manual says to do the "spill and fill" again, and I did. That is, put an oil pan under the drain plug and undo it with a 17mm spanner, then watch your expensive fluid fall back out again, you should get about 3 litres.  Then, put the drain plug back in, pump 3 litres back in through the fill plug with the fitting and pump, disconnect the fill fitting and replace the fill plug, start the car and run for another 3 minutes (making sure the temp is still under 40oC). The manual then asks for a 3rd "spill and fill" just like above. I also did that and so had put 13l in by now.  This time they want you to keep the engine running and run the transmission through R and D (I hope the wheels are still off the ground!) for a while, and allow the trans temp to get to 40oC, then engine off. Finally, back under the car and undo the fill plug to let the overfill drain out; it will stop running when fluid is at the top of the levelling tube. According to the factory, that is job done! Post that, I reconnected the fill fitting and pumped in an extra 0.5l. AMS says 1.5l overfill is safe, but I started with less to see how it goes, I will add another 1.0 litres later if I'm still not happy with the hot shifts.
    • OK, so regardless of whether you did Step 1 - Spill Step 2 - Trans pan removal Step 3 - TCM removal we are on to the clean and refill. First, have a good look at the oil pan. While you might see dirty oil and some carbony build up (I did), what you don't want to see is any metal particles on the magnets, or sparkles in the oil (thankfully not). Give it all a good clean, particularly the magnets, and put the new gasket on if you have one (or, just cross your fingers) Replacement of the Valve body (if you removed it) is the "reverse of assembly". Thread the electrical socket back up through the trans case, hold the valve body up and put in the bolts you removed, with the correct lengths in the correct locations Torque for the bolts in 8Nm only so I hope you have that torque wrench handy (it feels really loose). Plug the output speed sensor back in and clip the wiring into the 2 clips, replace the spring clip on the TCM socket and plug it back into the car loom. For the pan, the workshop manual states the following order: Again, the torque is 8Nm only.
    • One other thing to mention from my car before we reassemble and refill. Per that earlier diagram,   There should be 2x B length (40mm) and 6x C length (54mm). So I had incorrectly removed one extra bolt, which I assume was 40mm, but even so I have 4x B and 5x C.  Either, the factory made an assembly error (very unlikely), or someone had been in there before me. I vote for the latter because the TCM part number doesn't match my build date, I suspect the TCM was changed under warranty. This indeed led to much unbolting, rebolting, checking, measuring and swearing under the car.... In the end I left out 1x B bolt and put in a 54mm M6 bolt I already had to make sure it was all correct
    • A couple of notes about the TCM. Firstly, it is integrated into the valve body. If you need to replace the TCM for any reason you are following the procedure above The seppos say these fail all the time. I haven't seen or heard of one on here or locally, but that doesn't mean it can't happen. Finally, Ecutek are now offering tuning for the 7 speed TCM. It is basically like ECU tuning in that you have to buy a license for the computer, and then known parameters can be reset. This is all very new and at the moment they are focussing on more aggressive gear holding in sports or sports+ mode, 2 gear launches for drag racing etc. It doesn't seem to affect shift speed like you can on some transmissions. Importantly for me, by having controllable shift points you can now raise the shift point as well as the ECU rev limit, together allowing it to rev a little higher when that is useful. In manual mode, my car shifts up automatically regardless of what I do which is good (because I don't have to worry about it) but bad (because I can't choose to rev a little higher when convenient).  TCMs can only be tuned from late 2016 onwards, and mine is apparently not one of those although the car build date was August 2016 (presumably a batch of ADM cars were done together, so this will probably be the situation for most ADM cars). No idea about JDM cars, and I'm looking into importing a later model valve body I can swap in. This is the top of my TCM A couple of numbers but no part number. Amayama can't find my specific car but it does say the following for Asia-RHD (interestingly, all out of stock....): So it looks like programable TCM are probably post September 2018 for "Asia RHD". When I read my part number out from Ecutek it was 31705-75X6D which did not match Amayama for my build date (Aug-2016)
×
×
  • Create New...