Jump to content
SAU Community

Recommended Posts

hey guys, i have an rb30 turbo in my r31 wagon and was looking to upgrade the turbo- which would be the best for this motor ( its standard expect for fmic, pod, boost controller etc) have an rb20 red top turbo on it at the moment, but looking for something a bit bigger and not to expensive!

and what do u reconmend that i do to the car next (what mods)

cheers

:D

Link to comment
https://www.sau.com.au/forums/topic/309813-rb30-turbo-question/
Share on other sites

gotta go the forward facing plenum and injectors!

i have a 25/30 and a garret TO4B which will do 20psi no probs but i find its too laggy for my liking, i dont see full boost till 3500-4000rpm and the 30 bottom shouldn't really be revved more than 7000rpm which doesnt give you allot of time in 1st and 2nd gear.. so a drag off the lights is a little embarrassing if its not too far to the next set of lights..

In terms of cheap turbos, your going to find most will crap themselves first time you use them and shatter into your motor, so if you see a turbo sub 700-800 I would say dont touch (except for stock ones etc)

The best bang for buck turbos around here that are reliable are hypergears. Im sure Stao will be in here soon enough and give some recommendations.

Before you just look at upgrading the power mods ie. turbo, for your car to run correctly you HAVE to upgrade the supporting mods, which are things like:

larger injectors to flow more fuel into your motor to cope with the larger amount of air being pushed in by a larger turbo (so the air fuel ratio can stay on par)

ECU - the cars computer, to customize the maps of air fuel ratio, you will never get the most out of your car without one

Air flow meter- Im assuming the old 31's have one, if they do, it will probably also need an upgrade as it measures the amount of air being pushed into the motor.

Fuel pump - if you dont want your car to explode because there is not enough fuel in it then you have to have one, some tuners wont tune without a decent one.

THEN you can worry about the forward facing plenum etc... but for now thats just wanky... its not a necessity in your case.

get the above mods first and a decent turbo and you wont believe how much faster your car is. if you dont get the above mods, you might be able to squeeze 200-230rwkw from your current setup with a small highflowed standard turbo, which cost roughly 1100-1300ish to do, but seeing as you have the larger capacity motor, you can go a larger turbo without too much lag and have alot of power with it. The only problem is cash... you would probably be looking at about 2000-3000 to get the above then another 1200-2500 for a turbo, so there goes your cheap upgrade.

Adam

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...