Jump to content
SAU Community

Recommended Posts

Rb25det series 2 engine long motor (never been cracked open)

- incl: intake mani + plenum + TPS sensor + AFM

- incl: stock coilpacks

- incl: stock exhaust mani

- 150000 Kms done

- all pully's incl except for a/c

- no thermostat + no cover for the thermostat

- no injectors or rail

- only selling as package unless u have some1 wanting the other bits

- was running fine in the car

- head n block still intact

$1500 ono

any questions etc plz pm or txt 0414424902

Edited by 8znR33
Link to comment
https://www.sau.com.au/forums/topic/310588-rb25det-engine/
Share on other sites

Rb25det series 2 engine long motor (never been cracked open)

- incl: intake mani + plenum + TPS sensor + AFM

- incl: stock coilpacks

- incl: stock exhaust mani

- 150000 Kms done

- all pully's incl except for a/c

- no thermostat + no cover for the thermostat

- no injectors or rail

- only selling as package unless u have some1 wanting the other bits

- was running fine in the car

- head n block still intact

$1500 ono

any questions etc plz pm or txt 0414424902

Sorry my mistake its 1600 not 1500

Link to comment
https://www.sau.com.au/forums/topic/310588-rb25det-engine/#findComment-5118587
Share on other sites

hey mate i need the cam angle sensor and the coil pack igniter how much you want for them?

hey mate mines a series 2 engine has no igniter pack, as for the CAS not quite ready to separate that part with it yet.

Link to comment
https://www.sau.com.au/forums/topic/310588-rb25det-engine/#findComment-5145904
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...