Jump to content
SAU Community

Carputer Advice Needed

dodes47
 Share

Recommended Posts

g33k Community Regular

g33k

Posted
Posted

Hi mate,

Good work, sounds like you've done your fair bit of wiring in the past.

As for the OBDII side of things, sadly, the V35 is not JUST OBDII, Nissan have also added some variations to the standard which in turn mean that device isn't always compliant with every OBDII device. (As i found out when i purchased a EBD device)

Of the 3-4 cables i've tried the BlaZt is the only i've found to work. Thats not to say the one you have linked won't work, just that i've had no experience and would be hesitant to try it unless you've had some positive feedback from someone.

There is a whole article (search ref OBDII) somewhere on here about which protocols the device needs to support and so on.

Even my HUD as a few minor confusions.

Cheers,

T

Thanks

The screen came with a sliding mount at the back of it. I just reversed it and screwed it in to the cubby hole. There's already a hole on it anyways so i thought what the heck :(

As for the power, i opened up the eeepc and soldered two thin wires to the power button. If the cables get shorted, the computer turns on. So i just extended the wires and connected it to a $2 Jaycar button on the bottom of my dash.

The laptop is powered by a normal car charger with an 8 amp fuse just in case .

I saw that obd2 somewhere on the net. If i recall, they're selling it for $135 usd. Now i don't mind paying that much, but just curious, will this work? http://cgi.ebay.com.au/ws/eBayISAPI.dll?Vi...e=STRK:MEWAX:IT

If it does why the massive price difference?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Yeah the rule of thumb with an LS is 7psi per 1000rpm. That is decidedly not enough at 6800rpm. I mainly looked for the scenarios where knock started to be picked up and it was later in the session when things were hotter, and oil was thinner, and the pressure was lower than it should be. (i.e very horrible). I am hoping with thicker oil (I was running Penrite ten tenths 10-40, the manual specifies 10-30) that does not leak that it's much improved at that time!!! I am using Project Mu Club Racer CR pads. I'm also using the Project Mu 335C fluid. The symptoms imply that it was fluid that boiled, but no bubbles seemed pretty weird to me when I bled it today. I want to try Castrol SRF as it has a much higher wet temp but, well, I have new Project Mu fluid lol... so I should at least use that. The pedal on track was really noticable. It went from basically normal feeling to instantly near-floor. The car did pull up as before, it was just very much nearly at the floor before the brakes engaged. At that point I pretty much decided the day was very done, it did *kinda* come back during that very slow cooldown lap into the pits. Felt perfectly fine driving home.
    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      f**king around with the bro
    • fatz
      Beers and skylines Fatz style

      By fatz · Posted

      Ludenham   44.2 tops day no issues  
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      Then today, I went to visit a man with an r33 hat Peter and Road and Race sorted the alignment. As it is being set up for general track/hillclimbs etc it has a heap of caster (7o), less camber than I am used to (1o front and 2o rear, as the caster looks after that in turns without the braking downsides), 3mm front toe out and 0 toe rear. Will see how that goes and track tyre wear to see if it does need more camber, but adjsustment is also limited with nismo arms and adjustable bushes at only 1 end. It does have a bent inner tie rod on the driver's side front but as it came up within spec I'll just leave that as is. So, that is getting close to my chapter of this story....could of tidy ups then a shakedown in early October before it finds a new home.
    • Duncan
      Neil's R33 Gts-t Build

      By Duncan · Posted

      So, it went to Unigroup for a run in and tune on Friday, everything went (generally) well. In terms of fixes, the engine was good and there were no leaks. It needed plugs (I hadn't checked them because the coil pack cover was on a new engine and I couldn't imagine they weren't new.....but turns out the temporary plugs to just keep it sealed up were in there.....new plugs gapped to 0.8 and it was fine from there. Also, there was a little preload on the clutch slave which caused some slip. I haven't had the box off so I don't know what the clutch looks like; my guess it is brand new and the pedal had not been adjusted....backed that off a bit and it held fine. Last thing will have Dose crying....the idle especially when cold is a bit difficult between the cams, forward plenum, atmo blow off valve and an 80s air management system. It is fine when hot but a little uneven when cold, will see if I can sort or at least improve that one cold morning. Other than that, tuning went fine. It made 245 but was pulled back to 227 which 2 opportunities to improve in future. 1. The factory CAS is not great and was jumping around at high RPM, so Mark took 2 degrees out up top (that is why it stops making power and lost 20kw). Very safe this way and the extra power is available but will require a more modern ECU and better cam (or even better crank) sensor 2. The 2871 in factory housings is very big for a low mount, and the internal wastegate is too small, so it was creeping from mid range all the way to redline....the duty cycle on the boost controller is turned down a little for safety. That is much harder to fix, it would need a large external gate and that would require a whole bunch of other changes, so it will go as it is for now. It feels nice and healthy and safe, so should be good for about a billion laps like this.
×
×
  • Create New...