Jump to content
SAU Community

Smok1106

rad100

By rad100,
in New South Wales

 Share

Recommended Posts

rad100 Grand Master

rad100

Posted
Posted

hey,

well i have bought some rb26 rocker covers from SMOK1106 (simon),

im yet to receive the goods, i also transfered extra cash which he was supposed to refund to me..

im yet to see either of these..

i try calling, messaging.. all i get is a msg a day saying goods sent, money refunded when i get home..

still nothing.

now wondering if anyine has info on him i can use to get hold of him?

i have a addy and a mob so im ready to get on a flight to syd and get my stuff back..

any help would be great..

cheers adrian!

Link to comment
https://www.sau.com.au/forums/topic/317860-smok1106/
Share on other sites
Mitchee Proficient

Mitchee

Posted
Posted

I also have purchased some goods from Simon.

First item was a Plazmaman plenum which he dropped off to my dad's work and picked up cash. I was not there at the time to meet him, but my dad was and everything was fine. The plenum was in perfect condition as described and Simon was helpful over SMS. I agreed to purchase some polished RB26 covers from him the following week as I couldnt afford them at the time I purchased the plenum.

He gave me his bank details and I sent him the money, including $30 extra to cover postage costs. I have heard from him via SMS a couple of times saying that the covers were sent and that he would check with his post office.

I paid him 13/4, i got an SMS saying he would check with the post office on 22/4 and that was the last I heard from him.

I have managed to obtain his full name, address and home phone number. I dont want to say this guy is dodgy as he seems to be legitimate only from my first purchase, but im tempted to take this further if I dont hear anything back soon.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/317860-smok1106/#findComment-5204331
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...