Jump to content
SAU Community

Recommended Posts

Hay guys I've sold my car so now all this stuff has to go.

___

17x9 + 22, and 17x9.5 +30 polished mesh wheels. 5x114.3

Have to sell as my new car will have 33 brakes which these dont clear due to dish!

http://img10.imageshack.us/i/060ie.jpg/

http://img594.imageshack.us/i/061p.jpg/

$1300 no tyres, will trade see bottom of page

___

D1 Spec steering wheel with boss kit and trd horn

suit toyotas, came off ma70 and jzx90.

http://img694.imageshack.us/i/054ss.jpg/

$130

___ Rays wheel nuts in black toyota 12x1.5 (genuine)

Used but all in good cond. and all there, locknuts and key.

http://img263.imageshack.us/i/053vd.jpg/

$120

___

"GalPro" polished tapered wheel nuts 12x1.5

20 in total 18 with 19mm head and 2 with 21mm barely notice,

good if you already have lock nuts though.

http://img697.imageshack.us/i/065pt.jpg/

$50

___

JZX90/100 stock suspension good condition,

car was complied with these.

http://img121.imageshack.us/i/052hh.jpg/

$250

___

S13 Silvia boot lip spoiler

Carbon, not sure on brand maybe origin??

http://img15.imageshack.us/i/051oo.jpg/

$150

___

In SA pick up, possibly post some stuff

any queries call Hayden 0401 515 676

Looking for 33 gtr wheels for trade or stagea S2 RS coilovers

Edited by jzxxx90

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...