Jump to content
SAU Community

Recommended Posts

Have the following for sale. All items are negotiable and located in Ipswich.

Item: 6boost Rb26 manifold - to suit TV flanged turbo's, 50mm wastegate pipe, made for a 26/30 in a 32 gtr so it sits the turbo forward of the shockie tower so theres room for a 5" dump

Condition: Brand new

Price: $900

2ed9q8o.jpg

21l6dlz.jpg

Item: Argo RB30 21mm conrods

Condition: Brand new

Price: $950

1xyur4.jpg

wkhgye.jpg

2jytsy.jpg

Item: Aeromotive Pro Series fuel regulator

Condition: Brand new

Price: $350

102uq2o.jpg

Item: RB30 block & custom 4wd Billet Girdle.

Condition: New & used

Price: $1900

Comments: Block is std bore, it's been modified to suit the billet girdle (no oil pickup, de-burred and has been clearanced around the sides to bolt a 4wd sump)

ubjb4.jpg

5lumtx.jpg

10dvatf.jpg

f04ysy.jpg

2z4jsww.jpg

  • 2 weeks later...
Will you ship to Canada ??

Cant pm you as I do not have enough posts !!!

I can, but shipping would be be expensive.

Also the manifold and rods have sold.

hey bud... i already have an rb30 bottom end that has had EVERYTHING known to man done to it for a 26/30.. but it was built for my old car which was only going to be rear wheel drive..

now i want to convert that motor back to 4wd and was wondering where u got that girdle from??

and also why does it eliminate the oil pickup?? is it for a dry sump setup only??

thanks

hey bud... i already have an rb30 bottom end that has had EVERYTHING known to man done to it for a 26/30.. but it was built for my old car which was only going to be rear wheel drive..

now i want to convert that motor back to 4wd and was wondering where u got that girdle from??

and also why does it eliminate the oil pickup?? is it for a dry sump setup only??

thanks

The girdle i made and designed myself. I made 1 for a rwd rb30 and the one i have, for a 4wd rb30.

Reason it eliminates the internal oil pickup, is because i did not want to weaken the centre main cap by remove excess material from that area. Plus if your going to be building a big engine like that, you should atleast go external oil pump, if not dry sump.

Hey i think Rips does billet girdles, goodluck

That he does, but his a multi-piece system, mine is an all-in-one :D

well let me see what i can do.. i might be very keen on this... is the crank standard size??

big end and main??

  • 1 month later...

Girdle is sold. Only have fuel reg left.

Also have 2 of my 4wd adapter plates for $500 each.

34f1ooy.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...