Jump to content
SAU Community

Recommended Posts

Nismo LM GT3 17inch forged 2 piece rims good condition missing one center cap no rash :P

Rims will come up nice with a good clean and polish

Front 17x7 215/45 yoko a drive tyres pretty worn on inside otherwise not too bad

Rear 17x8 235/40 tyres in good condtion

$1500 neg or swap for r33gtr rims in good condition no rash, condition of tyres doest matter just need some for car to sit on.

Nissan OEM tinted bonnet protector S15

$50

HKS SSQV bov mint condtion, mounted on turbo outlet pipe on my S15. Will include this pipe in the sale with exchange for your standard pipe, so S15 buyers only sorry.

$250

Used KNN panel air filter for S15

$20

Contact via pm thanks located in brisbane, all items are plus postage

Cheers

Edited by Gts30t
Link to comment
https://www.sau.com.au/forums/topic/322634-nismo-gt3s-hks-ssqv/
Share on other sites

More parts

Bosch 044 fuel pump, used for 5000kms, has a very very tiny leak in it, was using it in the boot with a surge tank so the leak became a problem. No problems at all for intank use

$50 ono

Nissan S15 OEM tinted bonnet protector

$50 ono

S15 Eyelids

@50 ono

Blue anodised fuel pump bracket

$40 ono

post-4425-1275480774_thumb.jpg

  • 2 weeks later...
  • 2 weeks later...

Sorry man, i ended up keeping it was just after some quick cash for a holiday i was going on

HKS BOV still available

$200 with adaptor mounted on a sr20 intercooler pipe... dirt cheap considering its pretty much brand new

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...