Jump to content
SAU Community

Recommended Posts

Nismo LM GT3 17inch forged 2 piece rims good condition missing one center cap no rash :P

Rims will come up nice with a good clean and polish

Front 17x7 215/45 yoko a drive tyres pretty worn on inside otherwise not too bad

Rear 17x8 235/40 tyres in good condtion

$1500 neg or swap for r33gtr rims in good condition no rash, condition of tyres doest matter just need some for car to sit on.

Nissan OEM tinted bonnet protector S15

$50

HKS SSQV bov mint condtion, mounted on turbo outlet pipe on my S15. Will include this pipe in the sale with exchange for your standard pipe, so S15 buyers only sorry.

$250

Used KNN panel air filter for S15

$20

Contact via pm thanks located in brisbane, all items are plus postage

Cheers

Edited by Gts30t
Link to comment
https://www.sau.com.au/forums/topic/322634-nismo-gt3s-hks-ssqv/
Share on other sites

More parts

Bosch 044 fuel pump, used for 5000kms, has a very very tiny leak in it, was using it in the boot with a surge tank so the leak became a problem. No problems at all for intank use

$50 ono

Nissan S15 OEM tinted bonnet protector

$50 ono

S15 Eyelids

@50 ono

Blue anodised fuel pump bracket

$40 ono

post-4425-1275480774_thumb.jpg

  • 2 weeks later...
  • 2 weeks later...

Sorry man, i ended up keeping it was just after some quick cash for a holiday i was going on

HKS BOV still available

$200 with adaptor mounted on a sr20 intercooler pipe... dirt cheap considering its pretty much brand new

cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...