Jump to content
SAU Community

Recommended Posts

Have a 97 RS4 here that was wrapped round a pole by look of it.

I bought it to use parts for my wifes stagea I just bought..so no floor mats cargo net and cover as all in my stagea along with a few other bits and peices and possibly bonnet

Front end still good though guards have some dents

Has 101k's on clock

All completely standard no mods at all.

Let me know what you need and i'll send photos prices etc

Starting from $5.00

Located in Sydney

can email me airtech354 at hotmail dot com or PM me

Tks

Daniel.

post-3004-1276141031_thumb.jpg

post-3004-1276141042_thumb.jpg

post-3004-1276141053_thumb.jpg

post-3004-1276141060_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/324314-wrecking-97-rs4/
Share on other sites

Holy shit! Nasty smash...

I'm after the seat release handle surround in the boot, passenger side I'm pretty sure

posted to Adelaide

thanks sav

not wrong!!

$20 posted just confirm side for me if want it

Tks

Daniel.

Link to comment
https://www.sau.com.au/forums/topic/324314-wrecking-97-rs4/#findComment-5285769
Share on other sites

im after the plastic cargo barrier roof clip that sits right at the back drivers side..if is it grey and how much to post to vic

not sure if i have it i'll get a photo let me know if part you mean

Link to comment
https://www.sau.com.au/forums/topic/324314-wrecking-97-rs4/#findComment-5293019
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...