Jump to content
SAU Community

Recommended Posts

Hi there everyone

im moving to Melbourne from NZ next month and my plan is to buy a Skyline "obviously by me writing this" and i dont think my sheep will cut it at summer time there so ill leave it behind :/

I have a few questions as ive been doing some research into what mods i want to do first and all that, and to each there own opinions on what needs attention first but i havent been able to find much info on this

How much should a low Km (under 100 thou) R34 GTT - Manual (either 4 door or 2 door as each as just damn fine looking peices of automotive greatness) in good condition and road legal !! Cost???

ive been looking on car sales for around 4 months to get sort of a understanding average and i think its about around $15,000 does that seem right?

plus where are some good workshops in melbourne (mainly east) that do a good job and dont charge like im driving a dump like a ferrari as i plan to spend a bit more then a couple of K on this to get some more ponies from it so i need a good tuner n that

Cheers

Link to comment
https://www.sau.com.au/forums/topic/324446-new-from-nz/
Share on other sites

Hi Tim and Welcome :P

A 4 door will fetch a lower price than a 2. Are you after the R34 with much fruit on it?

Most of the R34 depreciation happened between mid '09 to early '10 so you're coming into the market at a good time I'd say.

Check any VIN# on a prospective R34 with the "VINS Fasted" thread here on SAU to see if the car came from Hokkaido or N. Honshu where they salt their roads in winter. You get the drift.

Even a $18500 2 dr R34 GT-T in great condition can be worth the dough.

Link to comment
https://www.sau.com.au/forums/topic/324446-new-from-nz/#findComment-5288823
Share on other sites

hmm Im not fussed on any extras if there are they are a bonus as i have a few plans i wanna do anyway, and i dont mind on spending more for better either, i just dont wanna step into something thats more for more problems ha, but thats awesome about the VIN # info thanks heaps now when im looking hard i can find something with the less problems haha awesome cheers terry!!

Link to comment
https://www.sau.com.au/forums/topic/324446-new-from-nz/#findComment-5288918
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
    • Yeah, I would have said the same. It makes me suggest that there are other things wrong, such that the ECU is totally unhappy with the broken sensor. The only other thought here is that maybe it is shorted, which might cause a different issue to the typical "disconnected" sensor.
×
×
  • Create New...