Jump to content
SAU Community

Recommended Posts

For Sale

1994 Nissan Laurel C34 Medalist V Turbo (LX Selection)

backdc.jpg

Specs on the model here ----> Nissan Laurel C34 INFO

This is, as far as I know, the only fully complied, registered and legal C34 Laurel in Australia. It has gone through the strict inspections at Regency in South Australia and passed. Perfect for someone who is looking for a very unique and legal import that can be used as a daily driver or for some spirited driving through the hills.

Mechanical:

RB25DET MANUAL (from an R33 Skyline), was originally an RB25DET Auto

Engine and Gbox have only 130 000kms (Odometer 212 000km)

New Bilstein Suspension all around

Exhaust with canon muffler

Nizmo 2-Way LSD

Short shift kit on Gearbox

ABS

Work 17inch rims

Front fog lamps

Complete option bodykit w/ moulded front lip, side skirts and rear pods

Registered until September 2010

Interior:

Top of the range Medallist model

Leather interior

Woodgrain dash

Electric windows, mirrors, seats

Electronic climate control

Alpine CD player

EcuTalk consult computer, Blue screen (Reads everything directly from the computer including fault codes. Also computes fuel consumption, 0-100 and 1/4mile times etc.) more info here ----> ECUTalk INFO

Central locking w/ Australian Standards immobiliser and Alarm system

Airbags

Tinted windows

Black two-tone paint

Spare parts:

Rear bumper – current one has some bumps and scratches from when the car was used in Japan. New one will need to be painted to match two-tone paint.

Gear shifter woodgrain surround – current one was modified during manual conversion. New one will also need to be modified.

Nissan FAST Software - this software allows you to find the Nissan part number of ANY part of the car, especially helpful because this car is so rare. It also has details of almost every Nissan released in Japan.

Condition:

This car is in great condition for its age and only has a few blemishes. Front driver and passenger seats have slight fading and cracking from sun damage. Rear seats are in great condition. Boot used to have a spoiler but has been removed and the mount holes are currently plugged up with rubber grommets. Paint is in great condition although there are some stone chips, as expected on the front, and the bumps as mentioned on the rear bar. Dash lights are a little dim during the day.

Pictures:

sidefrontmu.jpg

sideback.jpg

interiors.jpg

insidebackmy.jpg

enginegl.jpg

Price: PRICE DROP $14,500neg. No swaps. Finance Available, contact me for details!

Location: Adelaide, South Australia

Contact: PM, Reply or call 0416 143 662

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...